Hot Workability Investigation of an Fe-Al-Ta Alloy Using Deformation Processing Maps
Metals, 2023 Fe-Al-Ta alloys are expected to replace high-alloyed steels in steam turbine blades. However, the mechanical properties of the forged blades are still not optimal due to limited grain refinement during hot forging and the coarse-grained microstructure ...
Aliakbar Emdadi +2 more
doaj +1 more source
Investigation on Indices of Workability and Rutting Resistance for Wearing Course Mixtures
The Baltic Journal of Road and Bridge Engineering, 2017 Simple indices easily help to evaluate a performance of hot mix asphalt mixtures. This study aimed to develop a simple workability index and rutting resistance index for wearing course mixtures.
Tran Thanh Nhat, Osamu Takahashi
doaj +1 more source
Microstructure-Property Relationships in Cold Rollable, High-Strength α/β Alloys [PDF]
MATEC Web of Conferences, 2020 For decades Ti-6Al-4V has been the workhorse alloy for aerospace sheet applications due to its good balance of properties and the known ability to hot roll it with relative ease.
Foltz John W.
doaj +1 more source
Experimental and numerical analyses of magnesium alloy hot workability
Journal of Magnesium and Alloys, 2016 Due to their hexagonal crystal structure, magnesium alloys have relatively low workability at room temperature. In this study, the hot workability behavior of cast-extruded AZ31B magnesium alloy is studied through hot compression testing, numerical ...
F. Abbassi +4 more
doaj +1 more source
A laboratory study on cold-mix, cold-lay emulsion mixtures [PDF]
, 2009 This paper describes laboratory experiments and presents results for the performances of cold-mix, cold-lay emulsion mixtures. The main objective of the experiments was to evaluate and improve the properties of the cold mixtures.
Aderson A. +23 more
core +1 more source
HOT COMPRESSION TEST OF 9 Cr-1 Mo STEEL – NUMERICAL SIMULATION
Acta Metallurgica Slovaca, 2016 This paper is focused on the evaluation of formability of heat resistant steel type 9Cr-1Mo by laboratory numerical simulation – hot compression test confirmed by laboratory hot compression test.
Alica Fedoriková +6 more
doaj +1 more source
Towards more sustainable construction–application of superabsorbent polymers in cementitious matrices with reduced carbon footprint [PDF]
, 2018 Construction industry is constantly searching for sustainable innovations to mitigate negative environmental impacts. Ground granulated blast-furnace slag (GGBS) is a well-known supplementary cementitious material which contributes to reduction of energy
Alekrish +20 more
core +4 more sources
Experience with the use of warm mix asphalt additives in bitumen binders [PDF]
, 2018 In most European countries, Hot Mix Asphalt (HMA) technology is still being used as the standard for the production and processing of bituminous mixtures.
Capayova +23 more
core +2 more sources
Microstructure and mechanical properties of large size as-cast Ti-43Al-9V-0.2Y (at.%) alloy ingot from brim to centre [PDF]
, 2011 A Ti-43Al-9V-0.2Y (at.%) alloy ingot with the size of Ф160×400mm was prepared by vacuum arc remelting (VAR). The microstructure of the as-cast Ti-43Al-9V-0.2Y alloy was composed of B2/α₂/γ lamellar colonies and massive B2 and γ phases which were ...
Chen, Yuyong +3 more
core +2 more sources
Effect of pre-deformation on hot workability of super austenitic stainless steel
Journal of Materials Research and Technology, 2022 The hot compression behavior of 7Mo-0.37N-RE super austenitic stainless steel (SASS), subjected to solution treatment and pre-deformation, is systematically investigated in the temperature range of 900–1200 °C and strain rates of 0.01–10 s−1. The results
Xin Hu +5 more
doaj +1 more source