Results 31 to 40 of about 8,523 (209)
Effect of tribological conditions for properties thermal spraying
Production Engineering Archives, 2017 The present contribution deals with the influence of tribological conditions on coating quality. Two types of coatings were selected for analysis WC-WB-CO and WC-FeCrAl, to advise that a new type of coating - carbide green. These coatings were applied to
Landová Mariana, Brezinová Janette
doaj +1 more source
Journal of Electrochemical Science and Engineering, 2022 Inconel and micro and nano WC-12Co powders were deposited on AISI 4140 carbon steel by high-velocity oxy fuel (HVOF) coating and followed by laser surface modification. Laser power and scan speed were varied at different levels.
Shanmugasundaram Sivarajan +4 more
doaj +1 more source
Microstructure-based thermo-mechanical modelling of thermal spray coatings [PDF]
, 2015 This paper demonstrates how microstructure-based finite element (FE) modelling can be used to interpret and predict the thermo-mechanical behaviour of thermal spray coatings.
BOLELLI, Giovanni +5 more
core +1 more source
Revista de Metalurgia, 2008 En el presente trabajo se muestra la obtención, mediante la proyección térmica de alta velocidad (HVOF), de recubrimientos que presentan buenas prestaciones para la protección contra los procesos de erosión y oxidación que ocurren en el interior de las ...
J. M. Guilermany +3 more
doaj +1 more source
Evaluation of the synergistic erosion-corrosion behaviour of HVOF thermal spray coatings [PDF]
, 2016 The present study examines three High Velocity Oxy Fuel deposited coatings, Tungsten Carbide, Chromium Carbide and Aluminium Oxide, under slurry erosion-corrosion conditions.
Galloway, Alexander +3 more
core +1 more source
Relationships between Process Parameters, Microstructure and Adhesion Strength of HVOF Sprayed IN718 Coatings [PDF]
, 2010 Fundamental understanding of relationships between process parameters, particle in-flight characteristics and adhesion strength of HVOF sprayed coatings is important to achieve the high coating adhesion that is needed in aeronautic repair applications ...
Lyphout, Christophe +2 more
core +1 more source
Results in Engineering, 2023 SA 210C is the material for tube boiler which is generally coated with Fe-based and Ni-based to increase its resistance at high temperature. The methods of thermal spray coating which is mostly performed on the material is wire arc (WA) spray and high ...
Teguh Widjajanto +3 more
doaj +1 more source
steel research international, Volume 97, Issue 4, Page 2241-2249, April 2026.Cold spray deposition of stainless steel (grade: SS304) is evaluated for marine applications, with emphasis on martensitic transformation during impact. Analytical modeling, simulations, and experiments reveal that helium‐assisted spraying of fine powders promotes cooling below the martensitic start temperature, enabling up to ≈40% austenite to ...
Cal Vin Wong +4 more
wiley +1 more source
Computational simulation of liquid-fuelled HVOF thermal spraying
, 2009 Liquid-fuelled high-velocity oxygen–fuel (HVOF) thermal spraying systems are gaining more attentions due to their advantage of producing denser coatings in comparison to their gas-fuelled counterparts.
Gu, Sai, Tabbara, Hani
core +1 more source
Stuck on Glass: A Review of Polymer and Polymer Nanoparticle Composite Coatings in Glass Technology
International Journal of Ceramic Engineering &Science, Volume 8, Issue 2, March 2026.Representation of the different regions during the withdrawal stage of dip coating. As the substrate is pulled upward out of the coating solution, the solution is either dragged up with it by surface forces or falls back into the container from gravitational forces.
Shaylee M. Becerra +3 more
wiley +1 more source