Results 51 to 60 of about 80,527 (240)
Precipitation Simulations of the O‐Phase in Ti2AlNb Alloys Processed by Laser Powder Bed Fusion
Advanced Engineering Materials, EarlyView.Simulated and experimental evolution of the O‐phase volume fraction during postprocessing of a Ti‐21Al‐25Nb (at.%) alloy processed by laser powder bed fusion. With results of sensitivity to input parameters from a thorough and quantified analysis, the interfacial energy matrix/precipitate is the most relevant input parameter for the simulation of the O‐
Silvana Tumminello +7 more
wiley +1 more source
A Dislocation Perspective on Strength and Toughness in Ceramics
Advanced Engineering Materials, EarlyView.Dislocations in ceramics enjoy a long but yet under‐appreciated history. The three research waves for dislocations in ceramics highlight the topic evolution over the last 90 years. This review focuses on the impact of dislocation on strength and toughness in ceramics.
Xufei Fang
wiley +1 more source
Updated Norwegian In Situ Rock Stress Database [PDF]
, 2018 This thesis presents an updated Norwegian in situ rock stress database and collected in situ rock stress data. In situ rock stresses are the stresses that are present in the ground before any disturbance.
Simonsen, Aurora Louise Lucia
core +1 more source
Advanced Engineering Materials, EarlyView.A combined experimental–computational framework identifies energy‐dependent laser absorptivity for NiTi in laser powder‐bed fusion, applicable to conduction and transition modes. Single‐track experiments and thermofluid smoothed particle hydrodynamics simulations are coupled through inverse analysis of melt pool geometry.
Mohamadreza Afrasiabi +3 more
wiley +1 more source
The prediction and back analysis of excavation behaviour in Oxford Clay. [PDF]
, 1996 The work described in this thesis involved the prediction and back-analysis of ground movements and pore water pressures around a temporary excavation, lOm deep, 105m long and 35m wide (50m long and lOm wide at its base) in the heavily overconsolidated
Pierpoint, Nicholas David +1 more
core
Advanced Engineering Materials, EarlyView.This work shows that the mechanical performance of multimaterial digital light processing (DLP) printed thermoset composites is governed by resin compatibility and interfacial design rather than spatial patterning alone. Brittle and ductile resin combinations produced premature interfacial failure, while graded interfaces and mechanically compatible ...
Ahmed M. H. Ibrahim +3 more
wiley +1 more source
In previous practice, the differential strain analysis (DSA) method, relied upon for estimating vertical principal stress to resolve geological stress, has shown limitations in reliability.
Long ZHAO +8 more
core +1 more source
Advanced Engineering Materials, EarlyView.Experiments and thermophysical simulations were conducted to investigate the electron beam powder bed fusion electron beam (PBF‐EB/M) process for the γ′‐strengthened nickel‐based superalloy Inconel 738LC. The results demonstrate the impact of process‐induced microstructural variations on high‐temperature mechanical behavior, providing a basis for ...
Jan Niklas Petenati +11 more
wiley +1 more source
Development of in-situ SEM torsion tester for microscale materials
, 2019 An in-situ SEM (scanning electron microscope) micro-torsion tester with high resolution is developed based on electromagnetism. The torque is controlled and measured using a coil-magnet component. The torsion angle is measured by a non-contact transducer
Wang, Sufang +5 more
core +2 more sources
Advanced Functional Materials, EarlyView.DNA strands are employed both as dynamic linkers and nanoscale templates for the integration of Ag2S nanoparticles on MoS2, which in turn imparted photothermal responsiveness; this feature permits the selective cargo (fluorophore, quantum dots or an enzyme) release from the MoS2 surface in response to local heat induced by light irradiation.
Kai Chen +3 more
wiley +1 more source