Results 61 to 70 of about 196,492 (251)

Household Health Costs: Direct, Indirect and Intangible.

Iranian Journal of Public Health, 2014
This study aimed at identifying components of the household health costs.This study was a qualitative research conducted in two main phases. The first phase consisted of interviews with sample households selected in eight provinces of Iran.
Mehdi Yousefi, Abbas Assari Arani, Bahram Sahabi, Anoshirvan Kazemnejad, Somayeh Fazaeli   +4 more
doaj  

Indirect costs associated with ulcerative colitis: a systematic literature review of real-world data

BMC Gastroenterology, 2019
Background The economic burden of ulcerative colitis (UC), specifically related to indirect costs, is not extensively documented. Understanding and quantifying it is required by health care decision makers.
Joelle Constantin, Petar Atanasov, Daniel Wirth, Andras Borsi   +3 more
doaj   +1 more source

Influence of Scan Strategies in Electron Beam Powder Bed Fusion on Solidification, Microstructure, and High‐Temperature Compressive Properties of γ′‐Strengthened Inconel 738LC

Advanced Engineering Materials, EarlyView.
Experiments and thermophysical simulations were conducted to investigate the electron beam powder bed fusion electron beam (PBF‐EB/M) process for the γ′‐strengthened nickel‐based superalloy Inconel 738LC. The results demonstrate the impact of process‐induced microstructural variations on high‐temperature mechanical behavior, providing a basis for ...
Jan Niklas Petenati, Karthik Kumar Banku, Prasanth Bondi, Ivan Zhirnov, Yangyiwei Yang, Gordon Schmidt, Jürgen Christen, Georg Hasemann, Manja Krüger, Bai‐Xiang Xu, Bilal Gökce, Silja‐Katharina Rittinghaus   +11 more
wiley   +1 more source

Additive Manufacturing of Alumina‐Reinforced Elastomers

Advanced Engineering Materials, EarlyView.
Vat‐photopolymerized elastomers reinforced with platelet‐shaped alumina exhibited preferential orientation, reduced porosity, and significantly enhanced mechanical performance. A 3 wt% platelet loading increased tensile strength from 12.4 to 45.7 MPa, highlighting the critical role of filler morphology in elastomeric VPP composites.
Majid Barzegar Keyvani, Zongwen Fu, Robert Göstl, Hamed Shokri, Carmine Putignano, Gianluca Percoco, Bilal Gökce   +6 more
wiley   +1 more source

Uniform Amorphization of Crystalline Silicon Surfaces Enabled by Deep Ultraviolet Femtosecond Laser Pulses

Advanced Engineering Materials, EarlyView.
Deep‐UV (258 nm) femtosecond pulses enable uniform amorphous silicon writing on Si(100)/(111) with a six‐fold larger fluence amorphization window than NIR methods. Optimized fluence and overlap yield 20–45 nm uniform and continuous amorphous layers. Microscopy shows sharp interfaces, and real‐time reflectivity reveals nanosecond melt–resolidification ...
Wissal Benali, Magali Gregoire, Matys Guyard, Tatiana Itina, David Grojo, Pol Sopeña   +5 more
wiley   +1 more source

Superlubricity and Corrosion Inhibition Properties of Solvate Ionic Liquids in Hybrid Carbon Fiber Reinforced Plastic–Steel Interfaces

Advanced Engineering Materials, EarlyView.
Solvate ionic liquids lubrication reduced the coefficient of friction by ∼60% compared to dry sliding, reaching steady‐state values as low as 0.04–0.05. Corrosion weight‐loss measurements in 1 M HCl further demonstrated significant inhibition behavior, with only 100 ppm of [Li(G3)][TFSI] (∼68.5 μL/L) reducing corrosion‐product weight loss by 63 ...
Sameh Dabees, Timothy Harte, Bhagya Dharmasiri, Y. Athulya Wickramasingha, David J. Hayne, Daniel J. Eyckens, Luke C. Henderson   +6 more
wiley   +1 more source

Fabrication Routes for Ionic Conducting Fiber Strain Sensors

Advanced Engineering Materials, EarlyView.
Ionic conducting fiber strain sensors (ICFSs) offer compliant, textile‐integrable sensing. Thus far, the commercialization of ICFSs has been constrained by fiber fabrication routes. This review provides a fabrication‐centric analysis of ICFSs correlating processing strategies with material properties and scalability.
Leo John Kershaw, Zhanhong Yang, Anne Ladegaard Skov, Magdalena Skowyra   +3 more
wiley   +1 more source

A Novel Approach to Estimate the Transition Temperature via Dynamic Nanoindentation

Advanced Engineering Materials, EarlyView.
A new dynamic nanoindentation‐based method was developed that uses the stiffness ratio as an indicator of the elastic–plastic deformation contributions at different temperatures. The approach successfully identified transition temperatures in ferritic steel and distinguished them from continuously ductile austenitic steel.
Stefan Zeiler, Nikolaus Kostwein, Ronald Schnitzer, Christian Mitterer, Verena Maier‐Kiener   +4 more
wiley   +1 more source

Costs of illness progression for different multiple sclerosis phenotypes: a population-based study in Sweden

Multiple Sclerosis Journal - Experimental, Translational and Clinical, 2019
Background Little is known of how the cost of illness and health-related quality of life changes over time after a diagnosis of multiple sclerosis. Objectives The aim was thus to explore the progression of annual direct and indirect costs and health ...
Hanna Gyllensten, Andrius Kavaliunas, Chantelle Murley, Kristina Alexanderson, Jan Hillert, Petter Tinghög, Emilie Friberg   +6 more
doaj   +1 more source

Effect of Cu and CuP Additions on the Microstructure and Nanoindentation‐Based Fracture Behavior of CoNiAlSi Ferromagnetic Shape Memory Alloys

Advanced Engineering Materials, EarlyView.
Cu and combined Cu–P microalloying refine the microstructure and enhance the nanoindentation‐derived fracture resistance of CoNiAlSi ferromagnetic shape memory alloys without suppressing the martensitic transformation. Comparative SEM, DSC, and nanoindentation results reveal that the CuP‐containing alloy provides the most balanced response, achieving ...
Mehmet Demir
wiley   +1 more source