Results 51 to 60 of about 37,675 (355)
Interfacial formation of intermetallic Ni-Al-Ti systems formed by induction heating
Frontiers in Mechanical Engineering, 2022 Intermetallic systems of Nickel (Ni), Aluminium (Al), and Titanium (Ti) are candidates for lightweight materials that offer high-temperature resistance.
Tri Widodo Besar Riyadi +2 more
doaj +1 more source
Crystals, 2022 A high-quality joint of pressureless sintered SiC ceramic (PS-SiC) and stainless steel brazed by AgCu/AgCuTi brazing alloy was realized. The effects of brazing temperature and holding time on the interfacial microstructure and mechanical properties of PS-
Qiang Ma +4 more
doaj +1 more source
Influence of interfacial microstructure on the mechanical properties of SiC/SiBCN composites
Journal of Materials Research and Technology, 2023 SiC/SiBCN composites were prepared via polymer infiltration and pyrolysis technique (PIP) and the influence of the interfacial microstructure on the mechanical properties of the composites was investigated. In this paper, an amorphous SiOC layer was observed at the fiber-matrix interface for the first time.
Tingbo Wang +4 more
openaire +2 more sources
, 2016 Microstructure and the corrosion behaviour of friction stir weld region in an aluminium AA5083/AA7023 dissimilar joint was studied using SEM/EDS, potentiodynamic polarization, EIS and AFM/SKPFM techniques.
Sarvghad, Madjid +2 more
core +1 more source
Laser Powder Bed Fusion of Alumina: Effects of Scanning Strategies on External and Internal Defects
Advanced Engineering Materials, EarlyView.This study investigates how scanning strategies affect pure alumina in laser powder bed fusion. Linear 45° scanning yields uniform surfaces but high porosity, while the island‐concentric strategy provides higher density with through‐holes favorable for infiltration. Findings highlight pathways toward optimizing defect‐free alumina parts.
Mohamed Abdelmoula +7 more
wiley +1 more source
Advanced Engineering Materials, EarlyView.Powder metal processing provides scalable advantages in nanoporous (np) metal development. Mechanical alloying is used to produce unique precursors for hybrid nanopore formation by oxide reduction and dealloying. As demonstrated in np Ag, this approach improves process efficiency while promoting smaller ligaments and larger pores, both of which are ...
Mark A. Atwater, Oliver A. Fowler
wiley +1 more source
Cailiao gongchengCarbon fiber reinforced polymer （CFRP） has the characteristics of high specific strength/modulus and strong designability， which has been widely used in aerospace and transportation. CFRP is mainly composed of carbon fiber， resin matrix and the interface
ZHANG Hongbin +7 more
doaj +1 more source
Characterisation of the cold metal transfer (CMT) process and its application for low dilution cladding [PDF]
, 2011 The process characteristics of the synergic cold metal transfer (CMT) process have been examined for welding aluminium alloy. Utilising a simple backlighting system and through the arc monitoring the droplet transfer modes were identified.
Pickin, Craig Graeme +5 more
core +1 more source
Capillary wetting and interfacial phenomena in microstructures [PDF]
, 2019 Fluid penetration into capillary tubes resulting from the interplay between solid-liquid adhesive interactions and liquid-liquid cohesive interactions is a ubiquitous phenomenon. In nature, the rise of underground water in the soil is due to capillary pressure. Moreover, a wide variety of technological applications, e.g.
openaire +3 more sources
Advanced Engineering Materials, EarlyView.The corrosion performance of AlSi7Mg and AlSi10Mg alloys produced through selective laser melting (SLM) was examined under compressive stress in a chloride environment. Electrochemical analyses, including open‐circuit potential (OCP), potentiodynamic polarization (CPP), and electrochemical impedance spectroscopy (EIS), were complemented by scanning ...
Femi John Akinfolarin +2 more
wiley +1 more source