Results 11 to 20 of about 2,223,729 (213)

The Effects of Ozone Sterilization on the Chemical and Mechanical Properties of 3D-Printed Biocompatible PMMA [PDF]

open access: yesMicromachines
Since ozone is highly corrosive, it can substantially affect the mechanical and chemical properties of the materials; consequently, it could affect the applicability of those materials in medical applications.
Ivan Morosavljević   +5 more
doaj   +2 more sources

Measurement and modelling of combustion in a spark ignition engine [PDF]

open access: yes, 1991
This thesis was submitted for the degree of Doctor of Philosophy and awarded by Brunel University.A study has been conducted into the causes of cycle by cycle variations in combustion within a spark ignition engine, the best measured engine parameter to ...
Brown, Andrew Gavin
core   +7 more sources

Development and optimisation of two-line planar laser induced fluorescence technique for combustion measurements [PDF]

open access: yes, 2012
This thesis was submitted for the degree of Doctor of Philosophy and awarded by Brunel University.This study has focused on development, optimisation and implementation of the 2-line Planar Laser Induced Fluorescence (2-line PLIF) technique for ...
Anbari Attar, Mohammadreza
core   +7 more sources

Microstructure and diametral fracture strength of spark plasma sintered WC-6Co-0.2B and WC-6Co-0.5B ceramic composites from nanosized and metastable WC powders [PDF]

open access: yesCerâmica, 2022
The present work aimed at evaluating the microstructures and mechanical properties of spark plasma sintered WC-6 wt% Co ceramic composites doped with boron (0.2 and 0.5 wt%).
G. S. de Alencar e Silva   +5 more
doaj   +1 more source

Determination of chemical composition on internal surfaces of hollow reinforced concrete structures under the influence of corrosion [PDF]

open access: yesОмский научный вестник, 2020
The paper presents the results of experimental studies on the determination of corrosion products on the surface of reinforced concrete structures. Methods for creating samples with artificial electrocorrosion under conditions close to real operation ...
A. S. Bryukhova   +3 more
doaj   +1 more source

Flow and combustion in disc and pent-roof SI engines [PDF]

open access: yes, 2006
Reported in this thesis is a study of combustion in a disc-shaped combustion chamber spark ignition engine, and in-cylinder flow and combustion in an idealised pent-roof spark ignition engine. Both engines were skip fired, to remove residuals and ensure
Murad, Ahmad E. M. A
core   +5 more sources

Improving the accuracy of determining corrosion products in reinforced concrete structures by atomic emission spectrum analysis

open access: yesОмский научный вестник, 2023
To determine the composition of inhomogeneous samples using the method of laser-spark emission spectrometry, calibration dependences are used, which can have significant systematic errors that significantly affect the determination of the quantitative ...
A. A. Kuznetsov   +3 more
doaj   +1 more source

RESEARCH OF Al2O3 AND Al NANOPOWDER FORMATION PROCESSES IN PLASMA UNDER THE INFLUENCE OF DEFOCUSED DUAL LASER PULSES ON ALUMINUM IN THE AIR ATMOSPHERE

open access: yesФизико-химические аспекты изучения кластеров, наноструктур и наноматериалов, 2021
The influence of the magnitude and type of defocusing of twin laser pulses on the purposeful formation of the component and charge composition of laser plasma under the influence of twin laser pulses on a target made of aluminum alloy AD1 (LSS-1 ...
Kh. Bazzal   +5 more
doaj   +1 more source

Studies of processes of the precursor formation for production of CuAl2O4 nanoceramics at the effect of double laser pulses on AD1 and M2 alloys in the air atmosphere

open access: yesФизико-химические аспекты изучения кластеров, наноструктур и наноматериалов, 2021
A study of formation of mixed Al nanopowders, copper and aluminum oxides, and precursors for production of CuAlO2 and CuAl2O4 nanoceramics under the influence of double laser pulses with energy of 53 mJ and the interpulse interval of 10 microseconds on a
Maxim N. Kovalenko   +5 more
doaj   +1 more source

Effect of Cobalt Doping and Milling Time on Microstructure and Vickers Microhardness of the Spark Plasma Sintered (67-x)Ti-xCo-22Si-11B (x = 2 and 6 at-%) Alloys [PDF]

open access: yesMaterials Research, 2020
Ti-6Al-4V and TiAl-based alloys are widely used for fabricating the implantable orthopedic devices and automotive components, respectively. Ti6Si2B-based alloys are attractive for use in orthopedic components because their higher hardness, superior ...
Nelson Damásio Ferreira   +5 more
doaj   +1 more source

Home - About - Disclaimer - Privacy