Results 241 to 250 of about 21,417,156 (279)
Some of the next articles are maybe not open access.
Structural Turbulence of Pearlitic Steel 09G2S at Low-Temperature Impact Toughness
Physical Mesomechanics, 2020The study explores the effect of helical rolling on the low-temperature impact toughness of pearlitic steel 09G2S. Helical rolling in two modes was performed at T = 850°C in six passes through rolls of varied diameters with air cooling (mode I) and water quenching (mode II).
V. E. Panin +3 more
openaire +1 more source
Low Temperature Impact Toughness of Structural Steel Welds With Different Welding Processes
Influence of welding process and welding consumable on the impact toughness at low temperatures of the Heat Affected Zone (HAZ) and the weld metal in a structural steel weldment was investigated. A comparison of the low temperature impact toughness was made between the welded joints fabricated by Shielded Metal Arc Welding (SMAW) and Flux Cored Arc ...
Vuong Nguyen Van Do +2 more
exaly +2 more sources
Effect of residual aluminum on impact toughness of steel at low temperatures
Metal Science and Heat Treatment of Metals, 19591. The transitional embrittlement of low carbon steel depends on the contents of aluminum and the ferritic grain size. 2. The higher the rate of cooling of steel from the austenite range, the finer the grain and the lower the tough-to-brittle transition temperature.
E. I. Rabinovich +2 more
openaire +1 more source
Impact Toughness of Trace Element Doping Q460 at Low Temperature
2022The impact toughness test of 14 mm, 20 mm thickness 460 MPa anti-seismic and corrosion resistant steel (Q460) with the trace element dopant Ni, Mn, etc. had been carried out on SANS pendulum impact tester at 20, 0, -20, -40, -60, -80, -100°C, Charpy impact energy magnitude had been measured and plotted out.
openaire +1 more source
Enhancement of Impact Toughness in Mild Steel Weldments under Low Temperature Applications
Key Engineering Materials, 2020In this research, mild steel weldments are tested by varying nickel content into the weld beads. Three mild steel plates have been joined using three electrodes with similar chemical composition except nickel content 0%, 9-11% and 19-21% respectively, by SMAW process and keeping heat input constant at all.
Manjinder Singh +2 more
openaire +1 more source
Effect of Low Temperatures on Charpy Impact Toughness of Austempered Ductile Irons
Journal of Materials Engineering and Performance, 2002Impact properties of standard American Society for Testing Materials (ASTM) grades of austempered ductile iron (ADI) were evaluated at subzero temperatures in unnotched and V-notched conditions and compared with ferritic and pearlitic grades of ductile irons (DIs).
Mikhail V. Riabov +2 more
openaire +1 more source
Metallurgical Research & Technology, 2023
The effect of Mo content on impact toughness of the coarse-grained heat-affected zone (CGHAZ) in 420 MPa offshore engineering steels after 15 kJ/cm welding simulations is studied at low temperatures of −40, −60 and −80 °C. With increasing Mo content from 0.08 to 0.16 wt.%, the average size of the prior austenite grain in the CGHAZ is decreased from 150
Hailong Du +3 more
openaire +1 more source
The effect of Mo content on impact toughness of the coarse-grained heat-affected zone (CGHAZ) in 420 MPa offshore engineering steels after 15 kJ/cm welding simulations is studied at low temperatures of −40, −60 and −80 °C. With increasing Mo content from 0.08 to 0.16 wt.%, the average size of the prior austenite grain in the CGHAZ is decreased from 150
Hailong Du +3 more
openaire +1 more source
The impact toughness and mechanism of low-carbon steel fracture at low temperatures
Industrial laboratory. Diagnostics of materials, 2019The goal of the work is to study the effect of severe plastic deformation (SPD) on the impact toughness and fracture mechanism of St3sp low-carbon structural steel within a test temperature range of 293 – 213 K. The issues of deformation processing of steel St3sp billets using SPD method in conditions of the equal-channel angular pressing scheme (ECAP)
A. M. Ivanov, N. D. Kovalenko
openaire +1 more source
SSRN Electronic Journal, 2021
Ultrafine ferrite with a grain size range of 0.5-2 μm was introduced into low-temperature bainitic medium-carbon high-silicon steel through partially austenitization of cold-rolled tempered troostite followed by austempering at temperatures of 10 °C above martensite starting temperature.
TIng Zhao +4 more
openaire +1 more source
Ultrafine ferrite with a grain size range of 0.5-2 μm was introduced into low-temperature bainitic medium-carbon high-silicon steel through partially austenitization of cold-rolled tempered troostite followed by austempering at temperatures of 10 °C above martensite starting temperature.
TIng Zhao +4 more
openaire +1 more source

