Results 71 to 80 of about 504,825 (295)
Towards the production of 50'000 tonnes of low-carbon steel sheet for the LHC superconducting dipole and quadrupole magnets [PDF]
, 2002 A total of 50'000 tonnes of low-carbon steel sheet has been ordered for the LHC main magnets. After three years of production, about 10'000 tonnes of steel sheet have been produced by Cockerill-Sambre Groupe Usinor.
Babic, S +5 more
core +1 more source
Advanced Engineering Materials, EarlyView.Low‐cycle fatigue damage in Mn–Mo–Ni reactor pressure vessel steel is examined using a combined electron backscatter diffraction and positron annihilation lifetime spectroscopy approach. The study correlates texture evolution, dislocation substructure development, and vacancy‐type defect formation across uniform, necked, and fracture regions, providing
Apu Sarkar +2 more
wiley +1 more source
Understanding the interaction between a steel microstructure and hydrogen [PDF]
, 2018 The present work provides an overview of the work on the interaction between hydrogen (H) and the steel’s microstructure. Different techniques are used to evaluate the H-induced damage phenomena. The impact of H charging on multiphase high-strength
Depover, Tom +5 more
core +2 more sources
Programmed fatigue of low carbon steel [PDF]
, 1971 Fatigue crack propagation has been investigated in single edge notched mild steel specimens under constant and programmed loading conditions. Results have been analysed by the fracture mechanics approach and the Palmgren-Miner summation. Fracture surfaces were examined with a Cambridge Stereoscan scanning electron microscope.
openaire +1 more source
Advanced Engineering Materials, EarlyView.Four‐point bending tests are conducted in an argon atmosphere on commercial MgO‐C brick grades with and without MgO‐C recyclate from room temperature up to 1300 °C. No detrimental effect of the MgO‐C recyclates on bending strength is found. Instead, a decisive influence of the total carbon content is observed, with lower total carbon contents ...
Alexander Schramm +5 more
wiley +1 more source
, 2012 Austenite reversion during tempering of a Fe-13.6Cr-0.44C (wt.%) martensite results in an ultrahigh strength ferritic stainless steel with excellent ductility.
Choi, P. +5 more
core +1 more source
Advanced Engineering Materials, EarlyView.The formation of nonmetallic inclusions (NMIs) was investigated in this study, carrying out immersion tests for 30 min at a temperature of 1600°C with liquid high‐silicon electrical steel (Si ≈ 3 mass‐%) and different MgO–C refractories. Conventional MgO–C refractories were considered, as well as MgO–C refractories containing MgO–C recyclate and ...
Lukas Neubert +6 more
wiley +1 more source
Effect of Boron on Structure and Mechanical Properties of 780 MPa Low Carbon Bainite Steel
Teshugang, 2018 The tested low carbon bainite steel (/%: 0.08C, 0.11~0.13Si, 1.10~1.12Mn, 0.008〜0.009P, 0.002S, 0.21~0.23Ni, 0.020~0.021Ti, 0.003〜0.004Nb, 0~0.0010B, 0.0007~0.0008O, 0.0031~0.0033N) is melted by a 50kg vacuum induction furnace, rolled to 45mm plate ...
赵燕青 +6 more
doaj
Zhejiang dianliCurrently， large industrial enterprises， such as steel mills， have reduced electricity costs by participating in demand response programs； however， they have not yet achieved their carbon and emission reduction goals.
YAN Yue +6 more
doaj +1 more source
Studi Eksperimental Tentang Pengaruh Variasi Rapat Arus Pada Hard Chrome Electroplating Terhadap Karakteristik Permukaan Baja Karbon Rendah [PDF]
, 2010 The objective of the research is to investigate the effect of hard chrome electroplating on low carbon steel surface characteristic. This experimental research used low carbon steel as material that has been coated by hard chrome electroplating ...
Supriadi, H. (Harnowo)
core +1 more source