Results 11 to 20 of about 123,721 (262)
Low- and High-Cycle Fatigue Behavior of FRCM Composites [PDF]
Materials, 2021 This paper describes methods, procedures, and results of cyclic loading tensile tests of a PBO FRCM composite. The main objective of the research is the evaluation of the effect of low- and high-cycle fatigue on the composite tensile properties, namely the tensile strength, ultimate tensile strain, and slope of the stress–strain curve. To this end, low-
Calabrese A. S. +3 more
openaire +2 more sources
Low Cycle Fatigue of Precipitation Hardened Aluminum Alloy [PDF]
Engineering and Technology Journal, 2015 In this work, the influence of different heat treatments on the mechanical properties and fatigue life under low cycles of wrought 7075 aluminum alloy was experimentally investigated.
Dhafir S. Al-Fattal, Saif Khalid Mahmood
doaj +1 more source
Study of Fatigue Damage on Low Cycle Fatigue.
TRANSACTIONS OF THE JAPAN SOCIETY OF MECHANICAL ENGINEERS Series A, 1999 To study fatigue damage on low cycle fatigue, tensile tests after fatigue were carried out using cylindrical specimens, and the relationship between the change of residual fracture ductility and the cycle ratio was investigated. The main results obtained are as follows : (1) Until the last stage of fatigue life (N/Nf=0.9 ; crack length 1.5 mm), the ...
MORINO, Kazuhiro +2 more
openaire +2 more sources
New research findings on non-proportional low cycle fatigue [PDF]
MATEC Web of Conferences, 2019 One of the challenges regarding multiaxial fatigue damage predictions is non-proportional loading. Relevant studies have shown that these multiaxial loadings cause significant additional hardening and reduction in durability due to non-proportionality ...
Cernescu Anghel, Pullin Rhys
doaj +1 more source
Nihon Kikai Gakkai ronbunshu, 2021 In order to evaluate low cycle fatigue life under thermo-mechanical loading including high temperature regions, it is necessary to understand the basic deformation characteristics of a target material. In the case of thermo-mechanical loading, especially,
Kohei FUKUCHI +7 more
doaj +1 more source
Fatigue Properties of AZ31 and WE43 Magnesium Alloys [PDF]
Archives of Metallurgy and Materials, 2020 The paper presents low-cycle fatigue (LCF) characteristics of selected magnesium alloys used, among others, in the automotive and aviation industries.
G. Junak
doaj +1 more source
Low-Cycle Fatigue Characteristics of Selected Titanium, Magnesium and Aluminium Alloys [PDF]
Archives of Metallurgy and Materials, 2018 In the paper, on the basis of the performed tests, low-cycle fatigue characteristics (LCF) of selected light metal alloys used among others in the automotive and aviation industries were developed.
G. Junak
doaj +1 more source
Investigating the effect of extremely low cyclic fatigue in steel moment frames with reduced beam section connections [PDF]
Journal of Structural and Construction Engineering, 2020 Studies on damaged connections in recent earthquakes have shown that damage to some of the structures cannot be justified by the use of common failure mechanisms.
Mohsen Ghaderi +2 more
doaj +1 more source
International Journal of Naval Architecture and Ocean Engineering, 2022 Fracture induced failure of plates in hull structures subjected to in-plane biaxial low-cycle fatigue loading are generally a combination of accumulative plasticity and biaxial low-cycle fatigue damage.
Junlin Deng +4 more
doaj +1 more source
Catalogue of NIMS fatigue data sheets
Science and Technology of Advanced Materials, 2019 This paper summarizes the NIMS fatigue data sheets and makes a new gateway available to access them. The NIMS fatigue data sheets are a huge database of the fatigue properties of structural materials. This project covers fundamental fatigue properties at
Yoshiyuki Furuya +4 more
doaj +1 more source