Very high cycle fatigue of copper: Evolution, morphology and locations of surface slip markings [PDF]
, 2014 The surfaces of commercially pure polycrystalline copper specimens subjected to interrupted 20 kHz fatigue tests in the very high cycle fatigue regime were investigated.
VALES, Fréderic +4 more
core +1 more source
Metals, 2023 The total strain amplitude controlled low-cycle fatigue tests were performed at room temperature and 200 °C to clarify the influence of 0.5% Ag addition on the low-cycle fatigue behavior of an Al-5Cu-0.8Mg-0.15Zr-0.2Sc (in wt.%) alloy subjected to the ...
Ying Wang +4 more
doaj +1 more source
An experimental and finite element study of the low-cycle fatigue failure of a galvanised steel lighting column [PDF]
, 2009 This paper presents the results of a low-cycle fatigue test on a lighting column. The wind induced vibration phenomena responsible for low cycle fatigue in such structures is discussed and the failure mechanism is examined.
Taylor, Ian +2 more
core +3 more sources
Non-local energy based fatigue life calculation method under multiaxial variable amplitude loadings [PDF]
, 2013 Reliable design of industrial components against high cycle multiaxial fatigue requires a model capable of predicting both stress gradient and load type effects. Indeed, taking into account gradient effects is of prior importance for the applicability of
PALIN-LUC, Thierry +4 more
core +1 more source
A probabilistic model for the high cycle fatigue behaviour of cast aluminium alloys subject to complex loads [PDF]
, 2013 Lien vers la version éditeur: http://www.sciencedirect.com/science/article/pii/S0142112312002472This article is dedicated to the high cycle fatigue behaviour of cast hypo-eutectic Al–Si alloys and in particular the AlSi7Cu05Mg03 alloy.
PESSARD, Etienne +3 more
core +1 more source
Effect of Corrosion on the High Cycle Fatigue Strength of Martensitic Stainless Steel X12CrNiMoV12-3 [PDF]
, 2012 This paper addresses the effects of corrosion on the high cycle fatigue (HCF) strength of a high mechanical strength martensitic stainless steel (X12CrNiMoV12-3) that is used in aeronautic applications. HCF tests (between 105 and 107 cycles) were carried
PALIN-LUC, Thierry +4 more
core +1 more source
Low cycle fatigue of short fibre reinforced polyamides
, 2022 S.419-424In the automotive sector short-fibre reinforced polyamides play a major role for highly loaded components in under the hood application. In this field of use, the components are subject to different kinds of loading in the high cycle and the low
Stötzner, Norbert +3 more
core +1 more source
Modelling the role of non metallic inclusions on the anisotropic fatigue behaviour of forged steel [PDF]
, 2011 Forged components are known to show high cyclic and monotonic mechanical properties. This is mainly due to a better compactness and a finer microstructure introduced by the forming process. However, this good mechanical behaviour is sometimes a source of
D. Bellett +7 more
core +1 more source
Low Cycle Fatigue of Precipitation Hardened Aluminum Alloy [PDF]
Engineering and Technology Journal, 2015 In this work, the influence of different heat treatments on the mechanical properties and fatigue life under low cycles of wrought 7075 aluminum alloy was experimentally investigated.
Dhafir S. Al-Fattal, Saif Khalid Mahmood
doaj +1 more source
Low- and High-Cycle Fatigue Behavior of FRCM Composites [PDF]
Materials, 2021 This paper describes methods, procedures, and results of cyclic loading tensile tests of a PBO FRCM composite. The main objective of the research is the evaluation of the effect of low- and high-cycle fatigue on the composite tensile properties, namely the tensile strength, ultimate tensile strain, and slope of the stress–strain curve. To this end, low-
Calabrese A. S. +3 more
openaire +2 more sources