Results 71 to 80 of about 81,280 (285)

Glassy Amorphous Metal Injection Molded Induced Morphological Defects [PDF]

American Journal of Applied Sciences, 2016
Melt rheology in injection molded metastable supercooled liquid metal of Zr44-Ti11-Cu10-Ni10-Be25 alloy may induce selective crystallizations. High mobility Be, Cu and Ni atoms have been observed to differently crystallize in bulk metal glassy supercooled liquids.
AVERSA, Raffaella, Parcesepe, Daniela, Petrescu, Relly Victoria V., Chen, Guanying, Petrescu, Florian Ion T., Tamburrino, Francesco, APICELLA, Antonio   +6 more
openaire   +2 more sources

Broadband, Flexible, Skin‐Compatible Carbon Dots/Graphene Photodetectors for Wearable Applications

Advanced Functional Materials, EarlyView.
Broadband, flexible photodetectors integrating nitrogen‐rich carbon dots with single‐layer graphene on plastic substrates are demonstrated. A biocompatible chitosan–glycerol electrolyte enables efficient low‐voltage gating and on‐skin operation. The devices exhibit ultraviolet‐to‐near‐infrared response, mechanical robustness under bending, and verified
Nouha Loudhaief, Petr Rozhin, Ilaria Bertuol, Ali Raza, Leonardo Viti, Subhankar Roy, Enrico Cavarzerani, Luca Sbuelz, Matteo Brilli, Andrea Serinolli, Jacopo Nicoletti, Riccardo Piccoli, Sebastián Castilla, Simone Dal Zilio, Enrique Rodríguez‐Castellón, Miriam Serena Vitiello, Maurizio Selva, Flavio Rizzolio, Alvise Perosa, Giovanni Antonio Salvatore, Domenico De Fazio   +20 more
wiley   +1 more source

Deformation of Fe2Ni prepared by metal powder injection molding

Fenmo yejin jishu
In the process of the metal powder injection molding Fe2Ni, the deformation problem was present due to the uneven distribution of metal powders caused by the poor bonding of binder and shear heat generation.
MU Jianghan, LIU Shumei, LI Dajie, YANG Hangzhou, ZHOU Haitao   +4 more
doaj   +1 more source

Lithium Intercalation in the Anisotropic Van Der Waals Semiconductor CrSBr

Advanced Functional Materials, EarlyView.
We report the lithium intercalation in the layered van der Waals crystal CrSBr, revealing strongly anisotropic ion‐migration dynamics. Optical and electrical characterization of exfoliated CrSBr shows lithium diffusion coefficients that differ by more than an order of magnitude along a‐ and b‐directions, consistent with molecular dynamics simulations ...
Kseniia Mosina, Aljoscha Söll, Jiří Šturala, Martin Veselý, Petr Levinsky, Ondřej Kaman, Florian Dirnberger, Giuliana Materzanini, Nicola Marzari, Gian‐Marco Rignanese, Borna Radatović, Vlastimil Mazánek, David Sedmidubský, Zdeněk Sofer   +13 more
wiley   +1 more source

Chiral Nanohoops as an Efficient Spin Polarization System

Advanced Functional Materials, EarlyView.
Chiral conjugated nanohoops with a central dibenzopentalene unit exhibit 90% spin polarization at low voltage and high conductivity. These properties make them ideal components in molecular spintronics applications. Abstract A central challenge in molecular spintronics is to achieve a high spin polarization at low operating voltages and ambient ...
Anu Gupta, Philipp Seitz, Mathias Hermann, Birgit Esser, Ron Naaman   +4 more
wiley   +1 more source

Oxide Formation In Metal Injection Molding Of 316L Stainless Steel

Archives of Metallurgy and Materials, 2015
The effects of sintering condition and powder size on the microstructure of MIMed parts were investigated using water-atomized 316L stainless steel powder.
Jang Jin Man, Lee Wonsik, Ko Se-Hyun, Han Chulwoong, Choi Hanshin   +4 more
doaj   +1 more source

Progress in Titanium Metal Powder Injection Molding

Materials, 2013
Metal powder injection molding is a shaping technology that has achieved solid scientific underpinnings. It is from this science base that recent progress has occurred in titanium powder injection molding. Much of the progress awaited development of the required particles with specific characteristics of particle size, particle shape, and purity.
openaire   +2 more sources

Block Copolymers: Emerging Building Blocks for Additive Manufacturing

Advanced Functional Materials, EarlyView.
This review addresses how block copolymer (BCP) physics and rheology have led to the widespread use of BCPs in advanced additive manufacturing techniques, with particular emphasis on the untapped potential of these nanostructured materials toward achieving multi‐scale architected materials with unique, programmable material properties.
Alice S. Fergerson, Hemish B. Thakkar, Jiaen Wu, Emily C. Davidson   +3 more
wiley   +1 more source

Scalable Thermal Engineering via Femtosecond Laser‐Direct‐Written Phononic Nanostructures

Advanced Functional Materials, EarlyView.
This study demonstrates that femtosecond laser‐induced periodic surface structures (fs‐LIPSS) can function as phononic metasurfaces, reducing thermal conductivity below the plain thin‐film limit. Phonon Monte Carlo analysis reveals that the periodic structures restrict phonon mean free paths.
Hiroki Hamma, Roman Anufriev, Kazuyoshi Fushinobu, Masahiro Nomura, Byunggi Kim   +4 more
wiley   +1 more source

Metal Injection Molding Process Parameters as A Function of Filling Performance of 3D Printed Polymer Mold

MATEC Web of Conferences, 2018
Metal injection molding (MIM) is a swift manufacturing process, which can produce complex and intricate parts with good repeatability and accuracy. However, to quickly address low-volume demands of customized MIM parts, manufacturing of mold could be a ...
Qayyum Junaid A., Altaf Khurram, Rani A. Majdi A., Ahmad Faiz, Qadir Hafiz A., Amin Waseem   +5 more
doaj   +1 more source