Interfacial microstructure and shear strength of Ti-6Al-4V/TiAl laminate composite sheet fabricated by hot packed rolling [PDF]
, 2011 A two layer Ti-6Al-4V(wt%)/Ti-43Al-9V-Y(at%) laminate composite sheet with a uniform interfacial microstructure and no discernible defects at the interfaces has been prepared by hot-pack rolling, and its interfacial microstructure and shear strength were
Chen, Yuyong +5 more
core +1 more source
Fostering Innovation: Streamlining Magnetocaloric Materials Research by Digitalization
Advanced Engineering Materials, EarlyView.Magnetocaloric cooling (MCE) is an environmentally friendly refrigeration method with great potential. Optimizing MCE materials involves the preparation and screening of large quantities of samples, which in turn generates a large amount of data. A digitalization approach is presented that uses ontologies, knowledge graphs, and digital workflows to ...
Simon Bekemeier +17 more
wiley +1 more source
CORROSION BEHAVIOUR OF THE AZ31 MAGNESIUM ALLOY AND SURFACE TREATMENTS FOR ITS CORROSION PROTECTION [PDF]
, 2009 Nowadays environmental conservation forces the transportation industry to manufacture lighter and low emissions transport vehicles. In this contest, magnesium alloys have found increasing attention by the automotive industry because of their low density ...
Zanotto, Federica
core
Microstructural evolution and solidification behavior of Al-Mg-Si alloy in high-pressure die casting [PDF]
, 2013 Copyright @ 2013 ASM International. This paper was published in Metallurgical and Materials Transactions A, 44A(7), 3185 - 3197 and is made available as an electronic reprint with the permission of ASM International. One print or electronic copy may be
Ji, S +7 more
core +1 more source
Multimodal Data‐Driven Microstructure Characterization
Advanced Engineering Materials, EarlyView.A self‐consistent autonomous workflow for EBSP‐based microstructure segmentation by integrating PCA, GMM clustering, and cNMF with information‐theoretic parameter selection, requiring no user input. An optimal ROI size related to characteristic grain size is identified.
Qi Zhang +4 more
wiley +1 more source
Residual Stresses Induced by Dry and Cryogenic Cooling during Machining of AZ31B Magnesium Alloy [PDF]
, 2014 The major challenge of the Mg alloys has been their unsatisfactory corrosion resistance, which can be enhanced by improving the surface integrity. Cryogenic machining, where liquid nitrogen was used during machining, has been reported to improve the ...
MARQUES, Maria José +6 more
core
The PRIMA Thesaurus for Materials Science and Engineering
Advanced Engineering Materials, EarlyView.The PRIMA Thesaurus is a structured vocabulary designed to improve how materials science data is described and shared. Developed with input from multiple experts, it enables clear documentation of research workflows, data exchange, and reuse across platforms.
Rossella Aversa +8 more
wiley +1 more source
Hydrogen‐Assisted Fracture of Iron‐Based Fe–Ni–Al Alloys
Advanced Engineering Materials, EarlyView.Principal relations and fracture mechanisms of single‐phase and precipitate‐strengthened Fe–Ni–Al alloys subjected to prior electrochemical hydrogen charging are identified. The mechanisms of hydrogen effect on strength and microhardness are discussed, including hydrogen‐induced increase in microhardness and the role of hydrogen in fracture behavior ...
Nataliya Yadzhak +3 more
wiley +1 more source
Biodegradation and Mechanical Integrity of Magnesium and Magnesium Alloys Suitable for Implants [PDF]
, 2013 This book chapter deals with the fundamental aspects of corrosion of magnesium based alloys in bodily fluids and reviews the various techniques that can be used to tune their degradation rate.
Suriñach, Santiago +9 more
core +1 more source
Influence of Test Temperature and Test Frequency on Fatigue Life of Aluminum Alloy EN AW‐2618A
Advanced Engineering Materials, EarlyView.The influence of test temperature and test frequency on the fatigue life of EN AW‐2618A is investigated. High‐cycle fatigue tests are performed at different test temperatures and frequencies on the 1000 h/230°C overaged state. Both test parameters reduce fatigue life due to time‐dependent damage mechanisms.
Ying Han +5 more
wiley +1 more source