Results 101 to 110 of about 57,415 (319)
Characterisation of the cold metal transfer (CMT) process and its application for low dilution cladding [PDF]
, 2011 The process characteristics of the synergic cold metal transfer (CMT) process have been examined for welding aluminium alloy. Utilising a simple backlighting system and through the arc monitoring the droplet transfer modes were identified.
Pickin, Craig Graeme +5 more
core +1 more source
Review of Mg alloy corrosion rates
Journal of Magnesium and Alloys, 2020 A review of the literature confirmed that the intrinsic corrosion rate of high-purity Mg as measured by weight-loss is 0.3 mm/y in a concentrated chloride solution.
Andrej Atrens +6 more
doaj +1 more source
Performance Analysis of Abradable Coating Systems for Aircraft Gas Turbines
Advanced Engineering Materials, EarlyView.Three CoNiCrAlY/YSZ/MgAl2O4 abradable liner configurations on a nickel‐superalloy are evaluated by thermal‐gradient cycling and incursion tests. Laser ablation of the bondcoat and/or Y2O3‐stabilized ZrO2 (YSZ) intermediate layer increases mechanical interlocking and bonding for thick topcoats.
Hanna Heyl +4 more
wiley +1 more source
Mg/hydroxyapatite composites for potential bio-medical applications [PDF]
, 2010 This thesis was submitted for the degree of Master of Philosophy and awarded by Brunel University.Depending on an excellent combination of high mechanical property and fracture toughness, metallic biomaterials have been widely accepted for clinical ...
Li, Zibiao
core
Influence of corrosion and creep on intergranular fatigue crack path in 2XXX aluminium alloys [PDF]
, 2010 In this paper, two examples of the influence of time-dependent processes on crack path in two 2XXX aluminium alloys are presented. The first example is concerned with corrosion–fatigue crack growth resistance of a 2024 T351 alloy cracked in the S–L ...
Odemer, Grégory +2 more
core +1 more source
Metals, 2020 The present study investigated the effects of alloying and nano-reinforcement on the mechanical properties (microhardness, tensile strength, and compressive strength) of Mg-based alloys and composites.
Pravir Kumar +5 more
doaj +1 more source
Advanced Engineering Materials, EarlyView.Mg–Zn composites with a thickness of 0.21 mm were fabricated using roll bonding of a kirigami‐patterned Mg alloy inlay within a Zn matrix. Thermal activation following this process led to the formation of tailored intermetallic structures, which provided the composite with enhanced flexural strength.
Yaroslav Frolov +4 more
wiley +1 more source
In Vivo Corrosion of Two Novel Magnesium Alloys ZEK100 and AX30 and Their Mechanical Suitability as Biodegradable Implants [PDF]
, 2011 In magnesium alloys, the components used modify the alloy properties. For magnesium implants in contact with bone, rare earths alloys are commonly examined.
Tim Andreas Huehnerschulte +11 more
core +1 more source
Synthesis of Mg-Fe Alloys by Mechanical Alloying.
Journal of the Japan Society of Powder and Powder Metallurgy, 1999 Mg-x mass%Fe (x=0, 5, 10, 20) alloys were synthesized by mechanically alloying of elementary Mg and Fe powder for 180ks milling under 66kPa argon gas atmosphere using by a planetary ball milling. The obtained MA powders were composite materials of Mg and Fe, the reaction between Mg and Fe did not occurred during the MA process. After the MA process, Mg-
Kobayashi, Keizo +3 more
openaire +2 more sources
Advanced Engineering Materials, EarlyView.Identified through the use of statistical design of experiments and metallographic investigation, this study exposes the stochastic origins of intergranular cracks in blown powder laser beam directed energy deposition additive manufacturing of pure molybdenum. It further demonstrates a successful crack mitigation approach with direct correlation to the
Nathaniel J. Lies +2 more
wiley +1 more source