Results 11 to 20 of about 3,823,249 (407)
Mg-Alloys for Forging Applications—A Review [PDF]
Materials, 2020 Interest in magnesium alloys and their applications has risen in recent years. This trend is mainly evident in casting applications, but wrought alloys are also increasingly coming into focus. Among the most common forming processes, forging is a promising candidate for the industrial production of magnesium wrought products. This review is intended to
Nikolaus P. Papenberg +4 more
openaire +3 more sources
Tuning of the Mg Alloy AZ31 Anodizing Process for Biodegradable Implants
ACS Applied Materials and Interfaces, 2021 Coatings were grown on the AZ31 Mg alloy by a hard anodizing process in the hot glycerol phosphate-containing electrolyte. Anodizing conditions were optimized, maximizing corrosion resistance estimated by impedance measurements carried out in Hank’s ...
A. Zaffora +6 more
semanticscholar +1 more source
Recrystallization behavior and mechanical properties of AZ31B alloy during the hot-rolling process
Journal of Materials Research and Technology, 2023 In this work, microstructural characteristics, dynamic recrystallization and mechanical properties of the hot-rolled AZ31B were investigated. The results indicated that the different mechanisms of recrystallization are responsible for the microstructural
Chenhui Li +5 more
doaj +1 more source
Phase field simulation for grain refinement in dendrite growth of A356 aluminum alloy
Journal of Materials Research and Technology, 2023 Although A356 aluminum alloy has poor ductility and strength, the refinement of the initial α-Al phase has shown promise in improving these properties. The impact of grain refinement mechanisms on the organization and morphology of A356 aluminum alloys ...
Jiaqi Pei +4 more
doaj +1 more source
Journal of Materials Research and Technology, 2023 Tuning thermal treatment schedule has been confirmed as an effective technical route for achieving optimum properties of steels. In the present work, the intercritical quenching tempering(IQT) process was applied to steel 4145H for oil drilling tools ...
Zhuoran Feng +5 more
doaj +1 more source
Journal of Materials Research and Technology, 2023 The properties of high-entropy alloys (HEAs) depend primarily on the composition and content of elements. However, getting the optimal composition of alloying elements through the traditional ''trial and error'' method is challenging, especially for non ...
Xiaoyang Zhang +4 more
doaj +1 more source
Metals, 2021 The corrosion behavior of AZ31B Mg alloy exposed to Ringer’s, phosphate-buffered saline (PBS), Hank’s, and simulated body fluid (SBF) solutions for 4 days was investigated using electrochemical impedance spectroscopy (EIS), potentiodynamic polarization ...
F. R. García-Galván +3 more
semanticscholar +1 more source
Hardening-softening of Al0.3CoCrFeNi high-entropy alloy under nanoindentation
Materials & Design, 2023 The competition and balance mechanism between work hardening resulting from the surge in dislocations and material softening caused by plastic deformation during contact loading in Al0.3CoCrFeNi high-entropy alloy is unclear.
Qingwei Guo +6 more
doaj +1 more source
Investigation on nonequilibrium crystallization of highly undercooled Cu–Ni–Co alloys
Journal of Materials Research and Technology, 2023 Deep undercooling rapid solidification experiments of Cu–Ni–Co alloys were carried out using the molten glass purification cycle superheat method. 130 K, 177 K and 277 K undercooling degrees were obtained and analysed for Cu55Ni43Co2 alloy.
Yongchao Hao +5 more
doaj +1 more source
Quasicrystal-reinforced Mg alloys
Science and Technology of Advanced Materials, 2014 The formation of the icosahedral phase (I-phase) as a secondary solidification phase in Mg-Zn-Y and Mg-Zn-Al base systems provides useful advantages in designing high performance wrought magnesium alloys. The strengthening in two-phase composites (I-phase + α-Mg) can be explained by dispersion hardening due to the presence of I-phase particles and by ...
Kyun Kim, Young +2 more
openaire +2 more sources