Results 21 to 30 of about 57,415 (319)
Friction behavior of laser cladding magnesium alloy against AISI 52100 steel [PDF]
, 2012 The use of magnesium alloys in engineering applications is becoming increasingly important as a relatively low density allows savings in energy consumption and therefore reduction in air pollution.
J.E. Masse +3 more
core +1 more source
Journal of Materials Research and Technology, 2023 Investigating the surface morphology and microstructure of laser powder bed fusion (L-PBF) in solidification and optimizing process parameters is crucial for improving the accuracy and performance of cladding parts of GH3536 superalloy.
Dong Liu +4 more
doaj +1 more source
A multimodal data-driven design of low pressure die casting gating system for aluminum alloy cabin
Journal of Materials Research and Technology, 2023 The design of gating systems for large and complex thin-wall castings requires the application of empirical equations and a substantial number of iterative experiments.
Zhiqiang Duan +4 more
doaj +1 more source
Hardening of an Al-Cu-Mg alloy containing type I and II S phase precipitates [PDF]
, 2010 The effect of different thermo-mechanical treatments on the hardness of the 2024 (Al-Cu-Mg) alloy was studied. Artificial ageing was conducted through heating at a constant rate to specific temperatures followed by rapid cooling.
Starink, M.J., Wang, S.C., Parel, T.S.
core +1 more source
Groove Rolling Process of Mg/Al Bimetallic Bars [PDF]
Archives of Metallurgy and Materials, 2019 The paper presents the results of the experimental tests of Mg/Al bimetallic bars rolling process in classic and multi-radial modified round-oval-round passes.
S. Mróz, A. Stefanik, P. Szota
doaj +1 more source
Electroless Nickel Plating on AM60B Magnesium Alloy via Ti-Zr/Sol-Gel Composite Layer as Pretreatment [PDF]
Archives of Metallurgy and Materials, 2022 The Ti-Zr and Ti-Zr/sol-gel were used as pretreatment layers before the electroless nickel coating on AM60B magnesium alloy. Scanning Electron Microscopy was employed to investigate the surface morphology of the pretreated layers and applied electroless ...
Zhale Nazari +2 more
doaj +1 more source
Effect of homogenisation conditions on recrystallisation in the Al-Mg-Mn alloy AA5454 [PDF]
, 2007 The purpose of the present work is to understand the microstructure development and, particularly, to control the progress of recrystallisation in hot strip in the Al-Mg-Mn alloy AA 5454, which is typically used for the manufacture of structural ...
McLaren, A. J. +6 more
core +1 more source
Effect of Different Media on the Corrosion Behavior and Some Mechanical Properties of Al-Zn-Mg Alloy [PDF]
Engineering and Technology Journal, 2010 This work investigates the effect of different media (0.1N of NaOH, H2SO4and NaCl solution) on the polarization behavior of Al-Zn-Mg alloy and calculatessome of the corrosion parameters such as corrosion potential (Ecorr) and currentdensity (icorr ...
Majid Hameed Abdulmageed
doaj +1 more source
Twinning-mediated formability in Mg alloys [PDF]
Scientific Reports, 2016 AbstractMg alloys are promising candidates for automotive applications due to their low density and high specific strength. However, their widespread applications have not been realized mainly because of poor formability at room temperature, arising from limited number of active deformation systems and strong basal texture.
Suh, BC +4 more
openaire +4 more sources
Texture Evolution of AZ31 Magnesium Alloy Sheet at High Strain Rates [PDF]
, 2010 In the current contribution the mechanical behaviour at high strain rates of AZ31 magnesium alloy sheet is studied. Uniaxial deformation properties were studied by means of tensile split Hopkinson pressure bar (SHPB) at different temperatures.
Hurtado, I. +9 more
core +2 more sources