Surface roughness prediction in milling based on tool displacements [PDF]
, 2011 In this paper, an experimental device using non-contact displacement sensors for the investigation of milling tool behaviour is presented. It enables the recording of high frequency tool vibrations during milling operations.
MOREAU, Vincent +3 more
core +1 more source
Experimental evaluation of tool run-out in micro milling [PDF]
AIP Conference Proceedings, 2018 This paper deals with micro milling cutting process focusing the attention on tool run-out measurement. In fact, among the effects of the scale reduction from macro to micro (i.e., size effects) tool run-out plays an important role. This research is aimed at developing an easy and reliable method to measure tool run-out in micro milling based on ...
Attanasio, Aldo, Ceretti, Elisabetta
openaire +2 more sources
Development of Tool Wear Standards and Wear Mechanism for Micro Milling Ti-6Al-4V Alloy
Metals, 2022 With the rapid development of high-precision-device technology, new demands are put forward for micro milling. The size effect and low cutting energy of micro milling make the process expensive and difficult, especially for Ti-6Al-4V alloys.
Tao Zheng +3 more
doaj +1 more source
Cutting-Force Modeling Study on Vibration-Assisted Micro-Milling of Bone Materials
Micromachines, 2023 This study aims to enhance surgical safety and facilitate patient recovery through the investigation of vibration-assisted micro-milling technology for bone-material removal.
Peng Shang +5 more
doaj +1 more source
Simulation of the deflected cutting tool trajectory in complex surface milling [PDF]
, 2011 Since industry is rapidly developing, either locally or globally, manufacturers witness harder challenges due to the growing competitivity. This urges them to better consider the four factors linked to production and output: quality, quantity, cost and
Baili, Maher +9 more
core +1 more source
A novel run-out model based on spatial tool position for micro-milling force prediction
, 2021 The tool run-out significantly affects prediction of milling force, which is crucial for monitoring the micro-end-milling processes. For accurately predicting milling force, a novel tool run-out model is presented, which is based on spatial tool position
Lv, R +5 more
core +1 more source
Mechanical and physico-chemical study of sulphur additives effect in milling of high strength steel [PDF]
, 2012 The authors would like to express their appreciation to the TOTAL France Company for the technical and financial contribution to this study and to Béatrice Vacher for TEM images.Most machining operations require the presence of a cutting fluid in order ...
GENET, Nicole +11 more
core +1 more source
Cutting Edge Preparation of Micro Milling Tools
Procedia CIRP, 2014 AbstractMicro milling is commonly used industrially for the production of precision components. Premature tool wear is usually the reason for a short tool life of cemented carbide end mills. An approach to improve the tool wear behavior is the defined cutting edge preparation.
Uhlmann, E. +3 more
openaire +1 more source
The Identification of Tool Eccentricity Parameters in Micro-Milling
International Journal of Smart Home, 2016 Milling tool eccentricity has great influence in micro-milling. It could cause single edge cutting phenomenon, and effect machining quality and tool life. To recognize tool eccentricity parameters, on the basis of the tool eccentricity model, cutting edge trajectories are analyzed, and then a tool eccentricity identification method is proposed.
Zhang Xiang, Wang Guanglin
openaire +1 more source
Correlation between machining direction, cutter geometry and step-over distance in 3-axis milling: Application to milling by zones. [PDF]
, 2012 Computer-Aided Manufacturing (CAM) occupies an increasingly important role in engineering with all it has to offer in terms of new possibilities and improving designer/manufacturer productivity. The present study addresses machining of free-form surfaces
Senatore, Johanna +3 more
core +1 more source