Results 51 to 60 of about 64,749 (307)
Reconfigurable software architecture for a hybrid micro machine tool [PDF]
, 2015 Hybrid micro machine tools are increasingly in demand for manufacturing microproducts made of hard-to-machine materials, such as ceramic air bearing, bio-implants and power electronics substrates etc. These machines can realize hybrid machining processes
Chang, Wenlong +3 more
core +1 more source
Advanced Engineering Materials, EarlyView.Additive manufacturing provides precise control over the placement of continuous fibres within polymer matrices, enabling customised mechanical performance in composite components. This article explores processing strategies, mechanical testing, and modelling approaches for additive manufactured continuous fibre‐reinforced composites.
Cherian Thomas, Amir Hosein Sakhaei
wiley +1 more source
Finite element analysis of micro end mill and simulation of burr formation in machining al6061-t6 [PDF]
, 2014 The recent technological progressions in industries have offered ascent to the continually growing requests for microstructures, sensors, and parts. Micro-milling is a promising method to create these scaled down structures, sensors, and parts.
Kumar, Priyank, Patel, Ananya
core
Tailoring Functional Properties of Ti–Ni–Cu Shape Memory Alloy Thin Films for MEMS Actuators
Advanced Engineering Materials, EarlyView.A comprehensive study of critical parameters required to develop well‐performing Ti–Ni–Cu thin film shape memory alloy microactuators is provided. Materials science and device integration aspects are integrated by addressing structural and physical relationships using complementary characterization techniques as well as a practical fabrication solution
Elaheh Akbarnejad +6 more
wiley +1 more source
Experimental Investigation of Cutting Vibration during Micro-End-Milling of the Straight Groove
Micromachines, 2020 Micro-end-milling is a cutting technology that removes redundant material from machined workpieces by small-diameter end mills, and is widely used to manufacture miniature complex parts. During micro-end-milling, the cutting vibration caused by weak tool
Lijie Ma +4 more
doaj +1 more source
On high-speed turning of a third-generation gamma titanium aluminide [PDF]
, 2012 Gamma titanium aluminides are heat-resistant intermetallic alloys predestined to be employed in components suffering from high mechanical stresses and thermal loads.
A Beranoagirre +20 more
core +1 more source
Creep Properties and Deformation Mechanism of Additively Manufactured NiAl‐CrMo Composites
Advanced Engineering Materials, EarlyView.Additively manufactured NiAl‐CrMo composites contain numerous interfaces and cell boundaries that control their creep response. At 700°C under high applied stress, creep is dominated by dislocation‐controlled power‐law mechanisms. At 800°C–900°C and lower stresses, creep is primarily diffusion‐controlled along cell boundaries.
Jan Vollhüter +9 more
wiley +1 more source
Micromachines, 2020 Optimization of cutting parameters in micro-milling is an important measure to improve surface quality and machining efficiency of the workpiece. Investigation of micro-milling forces prediction plays a positive role in improving machining capacity.
Menghua Zhou +2 more
doaj +1 more source
The Identification of Tool Eccentricity Parameters in Micro-Milling
International Journal of Smart Home, 2016 Milling tool eccentricity has great influence in micro-milling. It could cause single edge cutting phenomenon, and effect machining quality and tool life. To recognize tool eccentricity parameters, on the basis of the tool eccentricity model, cutting edge trajectories are analyzed, and then a tool eccentricity identification method is proposed.
Zhang Xiang, Wang Guanglin
openaire +1 more source
A multi-sensor based online tool condition monitoring system for milling process [PDF]
, 2018 Tool condition monitoring has been considered as one of the key enabling technologies for manufacturing optimization. Due to the high cost and limited system openness, the relevant developed systems have not been widely adopted by industries, especially ...
Li, Weidong +4 more
core +1 more source