Results 121 to 130 of about 935,839 (291)

Influence of Test Temperature and Test Frequency on Fatigue Life of Aluminum Alloy EN AW‐2618A

Advanced Engineering Materials, EarlyView.
The influence of test temperature and test frequency on the fatigue life of EN AW‐2618A is investigated. High‐cycle fatigue tests are performed at different test temperatures and frequencies on the 1000 h/230°C overaged state. Both test parameters reduce fatigue life due to time‐dependent damage mechanisms.
Ying Han, Julian M. Rosalie, Jan Radners, Mauro Madia, Philipp von Hartrott, Birgit Skrotzki   +5 more
wiley   +1 more source

High‐Temperature Nanoindentation of Metals: Assessing Thermal Drift, Frame Compliance, and Chemical Composition Effects on the Reported Mechanical Properties

Advanced Engineering Materials, EarlyView.
Do not let thermal drift and instrument artifacts deceive high‐temperature nanoindentation results. We compare classical Oliver–Pharr and automatic image recognition analyses across steels and a Ni alloy to quantify these effects. Accounting for artifacts reveals systematic softening with temperature, while Cr and Ni additions boost resistance ...
Velislava Yonkova, Steffen Brinckmann, Ruth Schwaiger   +2 more
wiley   +1 more source

Enhanced Strength and Corrosion Resistance of Ti‐13Nb‐12Ta‐10Zr‐4Sn Alloy by Aging Treatment

Advanced Engineering Materials, EarlyView.
This work systematically investigates the effect of aging treatment on mechanical properties and corrosion behavior of vacuum arc‐melted Ti‐13Nb‐12Ta‐10Zr‐4Sn alloy. Owing to the increased α″ martensite, strength and corrosion resistance were significantly enhanced by aging treatment.
Yuhua Li, Rong Zhao, Qian Zhang, Haojie Wang, Yujing Liu, Lai‐Chang Zhang   +5 more
wiley   +1 more source

Bioinspired Shape‐Memory Hook Fasteners With Programmable Interlocking and Silent Release

Advanced Engineering Materials, EarlyView.
Bioinspired hook fasteners made from epoxy shape‐memory polymers are shown to switch between strong, secure attachment and gentle, silent release when heated. By combining programmable geometry and material response, these adaptive fasteners outperform commercial systems in strength and noise control, enabling new solutions for robotics, medical ...
Maria I. Vallejo Ciro, Manuel J. Carvajal Loaiza, Rahaf Homssi, Vanessa Restrepo   +3 more
wiley   +1 more source

A Study on the Results of Risk Analyses Applying the Concept of Rock Mass Stand-Up Time for Underground Mining Sites

Applied Sciences
Throughout all the countries in the world, including Vietnam, nations with well-established mining industries have undertaken extensive research on the stability of rock masses when constructing underground tunnels in varied geological conditions.
Phong Duyen Nguyen, Hiep Huy Nguyen, Hung Huu Dam, Manh Van Nguyen, Piotr Osinski, Eugeniusz Koda   +5 more
doaj   +1 more source

Copper Nanocrystallization in Anodic Oxide Films of Ti–Cu‐Based Bulk Metallic Glass and Its Effect on the Corrosion Resistance and Cytocompatibility

Advanced Engineering Materials, EarlyView.
Viktoriia Shtefan, Thorgund Nemec, Ute Hempel, Annett Gebert and coworkers demonstrate that anodic treatment of Ti–Cu‐based metallic glass in a nontoxic pyrophosphate electrolyte forms a protective bilayered Ti/Zr‐oxide film enriched with Cu nanocrystals.
Viktoriia Shtefan, Nora Fernández Navas, Thorgund Nemec, Ivan Kaban, Ute Hempel, Andrea Voss, Volker Hoffmann, Darius Pohl, Annett Gebert   +8 more
wiley   +1 more source

Photocurable Hypervalent Fluorinated Sulfur Containing Thin Films with Remarkable Hardness and Modulus

Molecules
Novel tetrafluoro-λ6-sulfanyl-containing oligomers prepared by visible light-promoted addition of 1,4-(bis-chlorotetrafluoro-λ6-sulfanyl) benzene or 1,3-(bis-chlorotetrafluoro-λ6-sulfanyl) benzene to either 1,4-diethynyl benzene or the 1,3-diethynyl ...
Kelly A. Bonetti, Deniz Rende, Michael Murphy, John T. Welch   +3 more
doaj   +1 more source

Evaluation of Plasticity and Creep Parameters From Tensile Stress–Strain Data for a Range of Strain Rates

Advanced Engineering Materials, EarlyView.
This plot compares experimental tensile stress–strain curves (with 4 different strain rates) and corresponding modelled curves (obtained using the optimised sets of Voce and Miller–Norton parameter values shown). The inferred M‐N values, characterizing the creep, are very similar to those obtained via conventional creep testing.
S. Ooi, R. P. Thompson, T. W. Clyne
wiley   +1 more source

Direct Metal Deposition of Graphene–Ti28Nb35.4Zr Matrix Composites With Enhanced Mechanical, Corrosion, and Biocompatibility Properties for Bone Implants

Advanced Engineering Materials, EarlyView.
Graphene nanoplatelet (0.1 wt.%) reinforcement significantly enhances the performance of β Ti‐28Nb‐35.4Zr alloy. Grain refinement, reduced water contact angle, and improved surface characteristics promote osteoblast adhesion and complete surface coverage after 7 days.
Khurram Munir, Jixing Lin, Yuncang Li, Li Zhu, Paul F. A. Wright, Cuie Wen   +5 more
wiley   +1 more source

3D (Bio) Printing Combined Fiber Fabrication Methods for Tissue Engineering Applications: Possibilities and Limitations

Advanced Functional Materials, EarlyView.
Biofabrication aims at providing innovative technologies and tools for the fabrication of tissue‐like constructs for tissue engineering and regenerative medicine applications. By integrating multiple biofabrication technologies, such as 3D (bio) printing with fiber fabrication methods, it would be more realistic to reconstruct native tissue's ...
Waseem Kitana, Indra Apsite, Leonid Ionov   +2 more
wiley   +1 more source