Results 71 to 80 of about 76,788 (307)

A data driven model-free predictive current control for grid-connected inverters

open access: yes电力工程技术
Traditional model predictive current control has been widely studied in the field of grid-connected inverter control due to its rapid response and multi-objective optimization capabilities.
Jindong YANG   +3 more
doaj   +1 more source

A Compact Spin‐Coated Graphene UWB Antenna for Breast Tumor Detection

open access: yesAdvanced Engineering Materials, EarlyView.
A compact, spin‐coated graphene ultra‐wideband patch antenna designed for breast tumor detection, capable of distinguishing between malignant and benign tumors. This innovative antenna can serve as an effective initial screening tool, particularly in resource‐limited settings such as rural areas, where access to advanced medical equipment like MRI and ...
Raja Rashidul Hasan   +9 more
wiley   +1 more source

A Strongly Robust and Easy-Tuned Current Controller for PMSM Considering Parameters Variation

open access: yesIEEE Access, 2020
This paper proposes an improved internal-model-control (IMC)-based proportional-integral (PI) current controller for a permanent magnet synchronous motor (PMSM) drive system to solve the parameter dependence problem.
Xinghe Fu   +3 more
doaj   +1 more source

Bounded stability in networked systems with parameter mismatch and adaptive decentralized estimation [PDF]

open access: yes2015 53rd Annual Allerton Conference on Communication, Control, and Computing (Allerton), 2015
Here, we study the ultimately bounded stability of network of mismatched systems using Lyapunov direct method. The upper bound on the error of oscillators from the center of the neighborhood is derived. Then the performance of an adaptive compensation via decentralized control is analyzed.
Saeed Manaffam   +3 more
openaire   +3 more sources

Composition‐Tuned Enhancement of the Anomalous Nernst Effect in FeCo–Pt Thin Films on Rigid and Flexible Substrates

open access: yesAdvanced Engineering Materials, EarlyView.
Disordered (Fe50Co50)1−xPtx thin films exhibit a pronounced anomalous Nernst effect (ANE) with a strong composition dependence on both rigid and flexible substrates. The transverse thermoelectric response peaks near 22.5 at.% Pt, accompanied by enhanced αxy/σxy scaling, thermal transport, and ANE sensitivity.
Mojtaba Mohammadi   +2 more
wiley   +1 more source

Hybrid Model Flux Observer for PMSM Sensorless Control System Considering Parameter Disturbances and Measurement Noise

open access: yesIEEE Access
The hybrid model flux observer integrates the advantages of the voltage and current models to improve its control performance. However, at low speeds, the observer is more sensitive to the noise present in the measurement signals, causing the observation
An-Fei Xu, Xuesong Zhu, Lei Yuan
doaj   +1 more source

Performance Analysis of Abradable Coating Systems for Aircraft Gas Turbines

open access: yesAdvanced Engineering Materials, EarlyView.
Three CoNiCrAlY/YSZ/MgAl2O4 abradable liner configurations on a nickel‐superalloy are evaluated by thermal‐gradient cycling and incursion tests. Laser ablation of the bondcoat and/or Y2O3‐stabilized ZrO2 (YSZ) intermediate layer increases mechanical interlocking and bonding for thick topcoats.
Hanna Heyl   +4 more
wiley   +1 more source

The Rise in Danish Unemployment: Reallocation or Mismatch? [PDF]

open access: yes
The two main competing theories for the outward shift in the uv-curve are investigated: Increased separations from employment at a given employment level (reallocation) and decreased levels of hires, given unemployment and vacancies (mismatch). Shifts in
Karsten Albæk, Henrik Hansen
core  

Solid‐State Diffusion and Intermetallic Phase Formation in Roll‐Bonded Mg–Zn Composites With Kirigami‐Patterned Inlay

open access: yesAdvanced Engineering Materials, EarlyView.
Mg–Zn composites with a thickness of 0.21 mm were fabricated using roll bonding of a kirigami‐patterned Mg alloy inlay within a Zn matrix. Thermal activation following this process led to the formation of tailored intermetallic structures, which provided the composite with enhanced flexural strength.
Yaroslav Frolov   +4 more
wiley   +1 more source

Additive Manufacturing of Continuous Fibre Reinforced Composites: Process, Characterisation, Modelling, and Sustainability

open access: yesAdvanced Engineering Materials, EarlyView.
Additive manufacturing provides precise control over the placement of continuous fibres within polymer matrices, enabling customised mechanical performance in composite components. This article explores processing strategies, mechanical testing, and modelling approaches for additive manufactured continuous fibre‐reinforced composites.
Cherian Thomas, Amir Hosein Sakhaei
wiley   +1 more source

Home - About - Disclaimer - Privacy