Results 131 to 140 of about 652,018 (291)

Investigation of Laser Ablation and Brush Pre‐Treatments for AlCu Cold Roll Bonding in Oxygen‐Free Conditions

open access: yesAdvanced Engineering Materials, EarlyView.
It is shown that laser ablation pretreatment under oxygen‐free conditions enables copper–aluminium bonding at significantly lower deformation degrees and improved properties compared to mechanical brushing. Laser ablation further increases interface contact area and induces favourable residual stress states and microstructural compatibility ...
Khemais Barienti   +11 more
wiley   +1 more source

Second Order Filter Distribution Approximations for Financial Time Series with Extreme Outliers [PDF]

open access: yes
Particle Filters are now regularly used to obtain the filter distributions associated with state space financial time series. Most commonly used nowadays is the auxiliary particle filter method in conjunction with a first order Taylor expansion of the ...
António Santos, J. Q. Smith
core  

Characterization of Nitinol Produced by Laser Powder Bed Fusion for Mechanical Metamaterial Applications

open access: yesAdvanced Engineering Materials, EarlyView.
Stabilization of L‐PBF Ni50.7Ti49.3 under low‐cycle loading was investigated. Recoverable strain after cycling was dependent on the amount of applied load. Recovery ratio was 53.4% and 35.1% at intermediate and high load, respectively. The maximum total strain reached 10.3% at a high load of 1200 MPa.
Ondřej Červinek   +5 more
wiley   +1 more source

Flight prototype regenerative particulate filter system development [PDF]

open access: yes
The effort to design, fabricate, and test a flight prototype Filter Regeneration Unit used to regenerate (clean) fluid particulate filter elements is reported.
Garber, P. J., Green, D. C.
core   +1 more source

Particle Filters

open access: yes, 2021
Both the particle and Kalman filters attempt to approximate the minimum mean-square error (MMSE) estimate of the time-varying parameter. In this scenario, a prior model of the time evolution of the parameter of interest is assumed before the MMSE estimation takes place.
openaire   +3 more sources

Reduction of Oxide Inclusions During the High‐Frequency Welding of Steel via a Nonthermal Ar/H2 Plasma Jet

open access: yesAdvanced Engineering Materials, EarlyView.
High‐frequency (HF) welding of steel is limited by oxide inclusions that degrade weld quality. This study demonstrates, for the first time, the integration of a nonthermal Ar/H2 dielectric barrier discharge (DBD) plasma jet into HF welding. Local plasma treatment provides effective shielding and in‐situ oxide reduction, resulting in markedly fewer and ...
Viktor Udachin   +4 more
wiley   +1 more source

Influence of an Argon/Silane Atmosphere on the Temperature of a Thermal Plasma

open access: yesAdvanced Engineering Materials, EarlyView.
The influence of a silane‐doped argon atmosphere on the chemical composition and temperature of a thermal nontransferring argon plasma is investigated using optical emission spectroscopy. As a result of the high amount of free electrons resulting from the stepwise ionization and dissociation of the silane molecule, even a silane addition of 0.01 vol ...
Lena Kreie   +4 more
wiley   +1 more source

Path sampling for particle filters with application to multi-target tracking

open access: yes, 2010
In recent work (arXiv:1006.3100v1), we have presented a novel approach for improving particle filters for multi-target tracking. The suggested approach was based on drift homotopy for stochastic differential equations. Drift homotopy was used to design a
Maroulas, Vasileios, Stinis, Panagiotis
core  

Handbook of Establishing and Maintaining Oxygen‐Free Atmospheres

open access: yesAdvanced Engineering Materials, EarlyView.
This study presents a practical framework for creating oxygen‐free atmospheres at ambient pressure using silane‐doped inert gases. The results show that ultra‐low oxygen levels and strongly reduced water content can be achieved through controlled silane dosing, drying systems, and sensor monitoring.
Sascha Jan Zimmermann   +3 more
wiley   +1 more source

Effect of Laser Deoxidation on Adhesive‐Bonded Aluminum in an Oxygen‐Free Atmosphere

open access: yesAdvanced Engineering Materials, EarlyView.
This study investigates laser ablation of aluminum under oxygen‐free conditions. The goal is to produce oxide‐free substrates that enable improved adhesive bonding with epoxy. Optimized laser parameters (90% overlap, 300 µJ) combined with oxide‐free substrates result in the highest tensile strength of the adhesive bond.
Sandra Gerland   +5 more
wiley   +1 more source

Home - About - Disclaimer - Privacy