Results 71 to 80 of about 1,889,452 (289)

Improved masers for X-band and Ku band [PDF]

open access: yes, 1973
Slow-wave structure of traveling-wave maser utilizes comb system which is comprised of ruby on one side and alumina on other; alumina also supports isolator material. Radiation at pump frequency is coupled to ruby through shaped alumina strips.
Clauss, R. C., Quinn, R. B.
core   +1 more source

Handbook of Establishing and Maintaining Oxygen‐Free Atmospheres

open access: yesAdvanced Engineering Materials, EarlyView.
This study presents a practical framework for creating oxygen‐free atmospheres at ambient pressure using silane‐doped inert gases. The results show that ultra‐low oxygen levels and strongly reduced water content can be achieved through controlled silane dosing, drying systems, and sensor monitoring.
Sascha Jan Zimmermann   +3 more
wiley   +1 more source

Ensemble averaged coherent state path integral for disordered bosons with a repulsive interaction (Derivation of mean field equations)

open access: yes, 2007
We consider bosonic atoms with a repulsive contact interaction in a trap potential for a Bose-Einstein condensation and additionally include a random potential.
Andersen   +40 more
core   +1 more source

Near‐Field Electrospinning Micro‐Printhead Achieves Precise Control of Nanofiber Deposition

open access: yesAdvanced Engineering Materials, EarlyView.
A micro‐printhead for near‐field electrospinning enables reproducible deposition of polymer nanofibers with diameters below 50 nm. Systematic parameter studies uncover the mechanisms linking operating conditions to fiber morphology, paving the way for precise and low‐cost nanoscale 3D manufacturing.As a high‐resolution, cost‐effective, and rapid ...
Han Xu, Dario Mager, Jan G. Korvink
wiley   +1 more source

直齿锥齿轮修形齿面安装误差敏感性分析

open access: yesJixie chuandong, 2014
On the basis of establishing the straight bevel gear meshing coordinate system with installation error,the way of using Gauss curvature of different surface to indicate installation error sensitivity of the straight bevel gear modification tooth surface ...
曹雪梅, 娄佳佳, 马战勇
doaj  

Tangle- and contact-free path planning for a tethered mobile robot using deep reinforcement learning

open access: yesFrontiers in Robotics and AI
This paper presents a tangle- and contact-free path planning (TCFPP) for a mobile robot attached to a base station with a finite-length cable. This type of robot, called a tethered mobile robot, can endure long-time exploration with a continuous power ...
Ryuki Shimada, Genya Ishigami
doaj   +1 more source

INFLUENCE OF CONTACT STATE ON PROPAGATION PATH OF RAIL SURFACE CRACK

open access: yesJixie qiangdu, 2022
In order to investigate the formation mechanism of fishhook shaped spalling defect on rail surface, the fatigue calculation model of wheel/rail rolling contact was established and the prediction method of crack propagation path was proposed based on the ...
MENG RuiJun, ZHAO Rui, WEI XiaoGang
doaj  

Annealed lattice animal model and Flory theory for the melt of non-concatenated rings: Towards the physics of crumpling

open access: yes, 2013
A Flory theory is constructed for a long polymer ring in a melt of unknotted and non-concatenated rings. The theory assumes that the ring forms an effective annealed branched object and computes its primitive path.
Grosberg, Alexander Y.
core   +1 more source

Removing Oxide Layers and Retaining Oxide‐Free Steel Surfaces by Polishing in Oxygen‐Free Atmosphere

open access: yesAdvanced Engineering Materials, EarlyView.
In this study, the efficacy of wet mechanical polishing under an oxygen‐free atmosphere for deoxidation and the retention of an oxide‐free steel surface are elucidated using X‐ray photoelectron spectroscopy. The methodology proved successful; however, the results were highly dependent on the preparation of the solvents used to clean the samples after ...
Friedrich Bürger   +2 more
wiley   +1 more source

Computerized generation and simulation of meshing of a novel crown gear coupling avoiding edge contact

open access: yesJournal of Advanced Mechanical Design, Systems, and Manufacturing, 2019
To avoid the occurrence of the hub tooth tip edge contact with the sleeve tooth root flank and the sleeve tooth tip edge contact with the hub tooth root flank, a novel crown gear coupling composed of a hub with profile crowning, longitude crowning, and ...
Yabin GUAN, Xiaohui YANG, Zongde FANG
doaj   +1 more source

Home - About - Disclaimer - Privacy