Results 121 to 130 of about 99,657 (326)

Rheological Issues of Phase Change Materials Obtained by the Complex Coacervation of Butyl Stearate in Poly Methyl Methacrylate Membranes

Energies, 2019
The research started from the fact that the coacervation process represents the process of formation of macromolecular aggregates after separation from the phase that takes place in a homogeneous polymer solution as a result of the addition of a non ...
Vasile Bendic, Dan Dobrotă, Tiberiu Dobrescu, George Enciu, Nicoleta-Elisabeta Pascu   +4 more
doaj   +1 more source

Low-density PMMA/MAM nanocellular polymers using low MAM contents: Production and characterization [PDF]

, 2019
Low-density nanocellular polymers are required to take advantage of the full potential of these materials as high efficient thermal insulators. However, their production is still a challenging task.
Athanassiou, Athanassia, Bernardo García, Victoria, Catelani, Tiziano, Martín de León, Judit, Pinto Sanz, Javier, Rodríguez Pérez, Miguel Ángel   +5 more
core   +1 more source

Gas check prevention during calendering of poly(vinyl chloride) films using poly(caprolactone)‐based additives

Journal of Vinyl and Additive Technology, Volume 31, Issue 2, Page 441-452, March 2025.
Three poly(caprolactone) (PCL)‐based additives of differing molecular weights were used as a secondary plasticizer to prevent gas checks in PVC films produced through calendering. Results showed that chemical and physicochemical properties influence the prevention or reduction of gas checks, unlike rheological properties including complex viscosity and
Luis F. Alvarez, Kushal Panchal, Richard L. Leask, Milan Maric, Jim A. Nicell   +4 more
wiley   +1 more source

Polymerizable ultraviolet stabilizers for outdoor use [PDF]

Polymeric materials that are stable enough to use outdoors without changes in excess of 20 years are investigated. Ultraviolet stabilizers or plastic materials were synthesized, polymerizable ultraviolet stabilizers, particularly of the 2(2-hydroxyphenyl)
Vogl, O.
core   +1 more source

Fracture load and three‐dimensional internal void analysis of direct composites used to restore worn molars

European Journal of Oral Sciences, EarlyView.
Abstract This study evaluated (1) the load‐bearing capacity of molars restored with direct occlusal veneers fabricated either from short‐fiber‐reinforced composite (SFRC) or particulate‐filled composite (PFC) and the presence of internal voids within the materials, and (2) effect of water storage on the fracture load and correlation between internal ...
Topias Yli‐Urpo, Jorma Määttä, Auli Suominen, Pekka K. Vallittu, Timo Närhi, Anna‐Maria Le Bell‐Rönnlöf, Jasmina Bijelic‐Donova   +6 more
wiley   +1 more source

Glass Transition Phenomena Semiannual Status Report [PDF]

Multiple glass transitions, heat capacities, and equation of state properties of polymer ...
Haldon, R. A., Rawlings, P., Schell, W. J., Simha, R.   +3 more
core   +1 more source

Erythrocyte ‘Feierzeit’ reaction: Novel filamentous and vesicular response to n‐butyl acetate

Journal of Microscopy, EarlyView.
Abstract Human erythrocytes (red blood cells; RBCs) undergo spontaneous disassembly after several hours of exposure to n‐butyl acetate (nBA). Images of the morphological changes were captured in time‐lapse sequences using differential interference contrast (DIC) light microscopy.
Philip W. Kuchel
wiley   +1 more source

Thin and Compact Versus Thick and Porous Fouling Layers in the Emulsion Polymerization of Acrylates and Vinyl Acetates Studied In Situ With a Quartz Crystal Microbalance (QCM)

Journal of Applied Polymer Science, Volume 143, Issue 21, June 5, 2026.
ABSTRACT Building on a quartz crystal microbalance with dissipation monitoring (QCM‐D), fouling in emulsion polymerization was compared between acrylate dispersions stabilized with a mobile, anionic surfactant and dispersions of poly(vinyl acetate‐co‐vinyl neodecanoate), PVAc, stabilized with polyvinyl alcohol, PVOH.
K. M. Hoffmann, O. Sidorow, W. Augustin, S. Scholl, A. Langhoff, D. Johannsmann   +5 more
wiley   +1 more source

Effective synthesis of electrically conductive polymer composites based on butyl methacrylate and graphene for 3D printing

Next Materials
This work is devoted to the development of electrically conductive polymer composite materials based on butyl methacrylate using the method of radical polymerization in Pickering emulsion in situ graphene oxide (GO), which was subsequently chemically ...
Mikhail Torkunov, Svetlana Girina, Natalia Ryvkina, Igor Chmutin, Oleg Uvarov, Alexander Gervald, Roman Toms, Maxim Rabchinskii, Grigorii Antonov, Alexander Gulin, Valery Melnikov, Kseniya Shiyanova   +11 more
doaj   +1 more source

Stabilized unsaturated polyesters [PDF]

, 1985
An unsaturated polyester, such as propylene glycolmaleic acid phthalic acid prepolymer dissolved in styrene is interpolymerized with an ultraviolet absorber and/or an antioxidant.
Borsig, E., Vogl, O.
core   +1 more source