Results 11 to 20 of about 22,579 (261)
Effect of maleic anhydride on mechanical properties and morphology of poly(lactic acid)/natural rubber blend [PDF]
Songklanakarin Journal of Science and Technology (SJST), 2020 Natural rubber grafted with maleic anhydride (NR-g-MA) was synthesized in an internal mixer at different loadings of MA content. NR-g-MA was used as a rubber modifier of poly(lactic acid) (PLA) and a compatibilizer of PLA/NR blends. Polymer blends were
Varaporn Tanrattanakul +2 more
doaj +1 more source
Unusual nonlinear switching in branched carbon nanotube nanocomposites
Scientific Reports, 2023 In this experimental study, we investigate the nonlinear dynamic response of nanocomposite beams composed of polybutylene terephthalate (PBT) and branched carbon nanotubes (bCNTs).
Walter Lacarbonara +6 more
doaj +1 more source
Preparation and Characterization of PMMA-HDPE and HDPE-PMMA Binary Polymer Blends [PDF]
Engineering and Technology Journal, 2017 A comparison was made on the mechanical characteristics of binary blends polymethylmethacrylate/ high density polyethylene (PMMA-%HDPE) and vice versa. Analysis of morphology by SEM has been also accomplished.
S.I. Salih +2 more
doaj +1 more source
Polymer Testing, 2023 Polymer dielectric materials operating at high temperatures are widely needed for advanced electrical and electronic systems. However, currently commercial polymer dielectrics are limited to relatively low operating temperatures.
Sen Niu +5 more
doaj +1 more source
Comparing Effect of Adding LDPE, PP, PMMA on The Mechanical Properties of Polystyrene (PS) [PDF]
Engineering and Technology Journal, 2015 In this research three groups of polymer blends have been prepared First groupincluded (Polystyrene (PS): Low density polyethylene (LDPE))While the Second group(included Polystyrene (PS): Polypropylene (PP)) and Third groups include (Polystyrene (PS ...
Sihama E. Salih +2 more
doaj +1 more source
Study of the Optical Constants of the PMMA/PC Blends [PDF]
Engineering and Technology Journal, 2011 The aim of the present work is concerned with the study of the optical constants of the PMMA/PC blend at different concentrations. The samples are casted as films from the PMMA and PC homopolymers and blend.
Marwa. R. F, Nahida. J. H
doaj +1 more source
Low-temperature synthesis method for the fabrication of efficient polymer-blend systems
Journal of Materials Research and Technology, 2021 It is essential that the particle sizes of polymer blends are controlled to ensure their superior properties. In this study, polymer blends at low temperatures were fabricated. Unlike conventional methods that use high temperatures, this method exhibited
Fares D. Alsewailem
doaj +1 more source
Confined Flow of Polymer Blends
Langmuir, 2008 The influence of confinement on the steady-state morphology of two different emulsions is investigated. The blends, made from polybutene (PB) in polydimethylsiloxane (PDMS) and polybutadiene (PBD) in PDMS, are sheared between two parallel plates, mostly with a standard gap spacing of 40 microm, in the range of shear rates at which the transition from ...
Tufano, C. +2 more
openaire +3 more sources
Progress of compatibilization methods in polymer blends
Cailiao gongcheng, 2019 Compatibilization of immiscible polymer blends is by far the most general and efficient strategy to convert multiphase polymer blends with poor miscibility into high performance polymer alloys. The concept and necessity of compatibilization of immiscible
MA Peng-fei +5 more
doaj +1 more source
New PCL/PEC Blends: In Vitro Cell Response of Preosteoblasts and Human Mesenchymal Stem Cells
Biology, 2022 In this study, new blends of PCL/PEC have been prepared in an easy manner by casting with the objective of obtaining new biomaterials to apply to tissue engineering and bone regeneration.
Jesus L. Pablos +5 more
doaj +1 more source