Results 121 to 130 of about 342,767 (296)
IEEE AccessIn wireless transceivers, the power amplifier (PA) is the most power-consuming and critical component, as it must meet stringent linearity and reliability requirements while maintaining high efficiency.
Muhammad Abdullah Khan +2 more
doaj +1 more source
New microelectronic power amplifier [PDF]
, 1968 Integrated push-pull power amplifier fabricated on a chip of silicon has interdigitated power transistors and is hermetically encapsulated in a beryllia flat package.
New, T. C.
core +1 more source
Advanced Engineering Materials, EarlyView.Stabilization of L‐PBF Ni50.7Ti49.3 under low‐cycle loading was investigated. Recoverable strain after cycling was dependent on the amount of applied load. Recovery ratio was 53.4% and 35.1% at intermediate and high load, respectively. The maximum total strain reached 10.3% at a high load of 1200 MPa.
Ondřej Červinek +5 more
wiley +1 more source
Design of an X-band high efficiency continuous-mode power amplifier
Dianzi Jishu YingyongTo improve the bandwidth and efficiency of power amplifier, a monolithically integrated X-band high-efficiency continuous B/J power amplifier is designed based on the 0.25 μm GaAs pseudomorphic high electron mobility transistor (pHEMT) process ...
Liu Hanxiao +3 more
doaj +1 more source
Laser beam modulation by an acousto optic mode locker [PDF]
, 2006 Nazariahmatdaud2006the characterization of beam modulation by acousto-optic mode locker is reported. Hene laser was employed as a source. Acousto-optic mode locker (aoml) was used to convert the continuous beam to become pulsed.
Bidin, Noriah +3 more
core
Advanced Engineering Materials, EarlyView.Geometry‐driven thermal behavior in wire‐arc additive manufacturing (WAAM) influences microstructural evolution during nonequilibrium solidification of a chemically complex Fe–Cr–Nb–W–Mo–C nanocomposite system. By comparing different deposits configurations, distinct entropy–cooling rate correlations, segregation, and carbide evolution are revealed ...
Blanca Palacios +5 more
wiley +1 more source
Advanced Engineering Materials, EarlyView.This article presents the design, modeling, and characterization of air‐pressure–actuated programmable vibroacoustic metamaterials (PVAMM). The study focuses on leveraging air pressure to dynamically tune resonance frequencies for effective noise attenuation.
William Kaal +2 more
wiley +1 more source
Advanced Engineering Materials, EarlyView.Disordered (Fe50Co50)1−xPtx thin films exhibit a pronounced anomalous Nernst effect (ANE) with a strong composition dependence on both rigid and flexible substrates. The transverse thermoelectric response peaks near 22.5 at.% Pt, accompanied by enhanced αxy/σxy scaling, thermal transport, and ANE sensitivity.
Mojtaba Mohammadi +2 more
wiley +1 more source
Tunable Balun Low-Noise Amplifier in 65nm CMOS Technology [PDF]
, 2014 The presented paper includes the design and implementation of a 65 nm CMOS low-noise amplifier (LNA) based on inductive source degeneration. The amplifier is realized with an active balun enabling a single-ended input which is an important requirement ...
Groinig, M., Sturm, J., Xiang, X.
core +1 more source
Effect of Laser Deoxidation on Adhesive‐Bonded Aluminum in an Oxygen‐Free Atmosphere
Advanced Engineering Materials, EarlyView.This study investigates laser ablation of aluminum under oxygen‐free conditions. The goal is to produce oxide‐free substrates that enable improved adhesive bonding with epoxy. Optimized laser parameters (90% overlap, 300 µJ) combined with oxide‐free substrates result in the highest tensile strength of the adhesive bond.
Sandra Gerland +5 more
wiley +1 more source