Results 41 to 50 of about 231 (210)
Numerical Study on Shear-Oriented Parameters in RC Beams with Openings Reinforced by Fe-SMA Rebars
Reinforced concrete (RC) beams with openings in shear spans exhibited a significantly reduced structural performance due to disruptions in load transfer mechanisms.
Mohamed Elkafrawy +3 more
doaj +1 more source
Curvature Change in Laser-Assisted Bending of Inconel 718
Laser heating is industrially applied to facilitate plastic shaping, especially for materials difficult to form due to their high hardness or brittleness.
Jacek Widłaszewski +3 more
doaj +1 more source
Electrodeposition in Structural Lattices of Variable Architectures
Electrodeposition enables geometry‐sensitive, autonomous void filling while simultaneously tuning chemical and mechanical properties. The development of approaches that can autonomously fill and heal material voids and yield composites with tailorable properties is increasingly relevant in engineering.
Yeong‐Man Kwon +3 more
wiley +1 more source
Review of the Structural Performance of Beams and Beam–Column Joints with Openings
The need for openings in RC structures has increased, but their presence significantly affects the performance and strength of the structures. While small openings can be managed with additional reinforcement, dealing with large openings in reinforced or
Narek Galustanian +4 more
doaj +1 more source
Additively manufactured AlCrFe2Ni2 with contrasting BCC/B2‐dominant and lamellar FCC + BCC/B2 microstructures exhibits the same pressure‐induced BCC/B2 → HCP transformation. Under laser heating at high pressure, HCP is destabilized, and a cubic BCC/B2 + FCC assemblage is recovered, while the lower‐scan‐speed microstructure transforms at a lower ...
Raimundas Sereika +5 more
wiley +1 more source
Pre-stressed high-strength concrete pipe piles (PHC pipe piles) have been widely used in actual soft foundation treatment projects due to their reliable quality, fast construction, assembly line production, and environmental friendliness.
Yunlong Yao +5 more
doaj +1 more source
Impact of Hydrogen Incorporation on Electronic and Magnetic Structure of X2CrNi18‐9 Stainless Steel
Hydrogen uptake in austenitic stainless steel alters both its electronic and magnetic structure. Seebeck measurements reveal hydrogen‐induced shifts in the electronic density of states, while neutron scattering uncovers nanoscale inhomogeneities that grow upon hydrogen incorporation, with the most pronounced effect observed in the PBF as‐built state ...
Torben Tappe +9 more
wiley +1 more source
Laser‐Induced Graphene from Waste Almond Shells
Almond shells, an abundant agricultural by‐product, are repurposed to create a fully bioderived almond shell/chitosan composite (ASC) degradable in soil. ASC is converted into laser‐induced graphene (LIG) by laser scribing and proposed as a substrate for transient electronics.
Yulia Steksova +9 more
wiley +1 more source
Analysis of methods for calculating the width of normal cracks in reinforced concrete structures
The width of normal cracks at the level of tensile reinforcement was calculated according to various methods using the data obtained from experimental tests on reinforced concrete beams (without reinforcement pre-stress), pre-cast reinforced concrete ...
Vidmantas Jokūbaitis +1 more
doaj +1 more source
Counterion Dependent Side‐Chain Relaxation Stiffens a Chemically Doped Thienothiophene Copolymer
Oxidation of a thienothiophene copolymer, p(g3TT‐T2), via different doping strategies and dopant molecules resulted in materials with similar oxidation levels and a high electrical conductivity of ≈100 S cm−1. However, mechanical properties varied significantly, with sub‐glass transition temperatures and elastic moduli spanning from –44°C to –3°C and ...
Mariavittoria Craighero +12 more
wiley +1 more source

