Results 71 to 80 of about 749,971 (303)
Testing and Numerical Modelling of Steel-Concrete-Steel with Stud Bolts Connectors Subject to Push-Out Loading [PDF]
Journal of Rehabilitation in Civil Engineering, 2019 Steel-concrete-steel (SCS) sandwich panels are composed of two steel plates with low thicknesses and high densities and strengths and one thick layer between both plates with low strength and density known as core that is composed of concrete.
Mohammad Golmohammadi +1 more
doaj +1 more source
Advanced Engineering Materials, EarlyView.Trace additions of Sn and Sr combined with a two‐step aging treatment are shown to enhance the microstructure and performance of Al–Zr–Sc conductor alloys. Strength and electrical conductivity increase concurrently through accelerated precipitation of fine Al3(Sc, Zr) precipitates and improved dislocation resistance, offering a cost‐effective pathway ...
Quan Shao +3 more
wiley +1 more source
Near‐Field Electrospinning Micro‐Printhead Achieves Precise Control of Nanofiber Deposition
Advanced Engineering Materials, EarlyView.A micro‐printhead for near‐field electrospinning enables reproducible deposition of polymer nanofibers with diameters below 50 nm. Systematic parameter studies uncover the mechanisms linking operating conditions to fiber morphology, paving the way for precise and low‐cost nanoscale 3D manufacturing.As a high‐resolution, cost‐effective, and rapid ...
Han Xu, Dario Mager, Jan G. Korvink
wiley +1 more source
Grade-two resistance screw shear connector behaviour for a composite section system
Ingeniería e Investigación, 2008 Screw shear connectors have been most commonly used in Colombia for many years; however, there is no current design methodology justifying its use in composite sections and prevailing rules insist that elements used as shear connectors must be tested ...
Maritzabel Molina Herrera +2 more
doaj
Advanced Engineering Materials, EarlyView.A combined finite element and phase‐field approach predicts the evolution of microstructure during the directional solidification of Ni‐based superalloys. The model reveals how withdrawal rate, temperature gradient, and wall thickness control the dendrite spacing, highlighting the strong effect of surface regions in thin sections where dendrite growth ...
Sean Böhm +3 more
wiley +1 more source
, 1995 The application of push-out test to characterize the mechanical behavior of interfaces in Metallic and Intermetallic Matrix Composites (MMCs and IMCs) is studied using Finite Element Method.
N. Chandra, C. R. Ananth
core +1 more source
Advanced Engineering Materials, EarlyView.A novel workflow for investigating hydride vapor phase epitaxy for GaN bulk crystal growth is proposed. It combines Design of experiments (DoE) with physical simulations of mass transport and crystal growth kinetics, serving as an intermediate step between DoE and experiments.
J. Tomkovič +7 more
wiley +1 more source
Influência da contaminação da dentina radicular sobre a resistência de união de um cimento resinoso autoadesivo [PDF]
, 2015 Dissertação (mestrado) - Universidade Federal de Santa Catarina, Centro de Ciências da Saúde, Programa de Pós-Graduação em Odontologia, Florianópolis, 2015.O objetivo desta pesquisa foi determinar a resistência de união (RU) de um cimento resinoso ...
Costa, Débora Delai
core
Contemporary Clinical Dentistry, 2019 Background: To increase the push-out bond strength of endodontic materials, newer obturation materials and obturation techniques are being introduced.
Mohammed Khwaja Moinuddin +4 more
doaj +1 more source
Advanced Engineering Materials, EarlyView.This plot compares experimental tensile stress–strain curves (with 4 different strain rates) and corresponding modelled curves (obtained using the optimised sets of Voce and Miller–Norton parameter values shown). The inferred M‐N values, characterizing the creep, are very similar to those obtained via conventional creep testing.
S. Ooi, R. P. Thompson, T. W. Clyne
wiley +1 more source