Results 71 to 80 of about 1,366 (195)
ABSTRACT Objectives This study evaluated the effects of material and surface condition (glazed vs. polished after simulated occlusal adjustment) on translucency parameter, contact angle, and flexural strength of four monolithic zirconia. Materials and Methods Disk‐shaped specimens (n = 80, Ø12 × 1 mm) were fabricated from four monolithic zirconia ...
Kelli Nunes Monteiro +5 more
wiley +1 more source
Bond strength enhancement for additively manufactured zirconia: Micro‐retentive design approach
Abstract Purpose To investigate the effect of digitally designed micro‐retention features on the bond strength of additively manufactured (AM) zirconia copings. Materials and Methods Sixty titanium base abutments (NobelParallel, NobelBiocare), pretreated with 50 µm alumina particles were divided into four groups (n = 15 per group); one group with ...
Rama B. Al‐Rashdan +5 more
wiley +1 more source
Hydraulic fast‐setting calcium silicate cement for crown cementation
Abstract Purpose This study evaluated film thickness, diametral tensile strength (DTS), and crown retentive strength of hydraulic fast‐set calcium silicate cement (fast‐set CSC) compared to conventional luting cements. Materials and Methods Fast‐set CSC was compared to zinc phosphate cement and glass ionomer cement.
Atefeh Nemati Karimooy +3 more
wiley +1 more source
Wheat Yield Response to Organic Fertilisers Depends on Drought Timing in a Sandy Soil
ABSTRACT Organic fertilisers enhance crop drought resilience by improving nitrogen (N) and phosphorus (P) use efficiency and soil‐plant water relations. However, the underlying mechanisms governing their effects across different drought timings in wheat under sandy soils remain unclear.
Muhammad Kamran +4 more
wiley +1 more source
ABSTRACT This study was conducted to assess the impact of different agricultural practices on the physical quality and the carbon and nitrogen stocks of anthropogenic soils used by smallholder farmers in Central Amazonia, Brazil. Undisturbed and disturbed soil samples were collected at three depths (0–0.10 m, 0.10–0.20 m, and 0.20–0.30 m), with five ...
Heitor Marcel da Silva Ribeiro +9 more
wiley +1 more source
Laser Ablation Sampling With Low‐Power Plasma: A LA‐MIP‐MS Instrument for Spaceflight
ABSTRACT Rationale Inductively coupled plasma (ICP) is a commonly used ion source for mass spectrometry‐based chemical analysis of a wide range of materials. Traditional ICP ion sources use high power (> 1000 W) and significant gas flow (> 10 L/min), rendering them unsuitable for spaceflight, as they are too resource‐intensive for planetary spacecraft.
Benjamin J. Farcy +11 more
wiley +1 more source
Gd‐doped BFO (BGFO) exhibits a ∼2‐order reduction in leakage current owing to its lowest content of oxygen vacancies. This leads to a ∼2.5‐fold increase in remnant polarization. These improvements in BGFO effectively boost charge separation and transportation, resulting in the greatest incident photon‐to‐current efficiency of 12.9 ± 0.73% and a ∼1.5 ...
Ming‐Wei Chu +7 more
wiley +1 more source
A sustainable electrospinning technique produces LATP ceramic nanofibers that form continuous Li⁺‐conductive pathways within composite solid electrolytes. The resulting quasi‐solid‐state batteries combine the strength of ceramic nanofibers with the flexibility of polymers, delivering high critical current density and excellent rate performance at room ...
Sivaraj Pazhaniswamy +3 more
wiley +1 more source
Development and Testing of a Low‐Cost Soil Moisture Sensor for Real‐Time Irrigation Scheduling
ABSTRACT Effective irrigation scheduling is essential for improved water management in irrigated areas, with soil moisture monitoring recognized as one of the most effective methods. However, challenges such as the high cost of sensors and the difficulties in monitoring large areas hinder their practical application, particularly for smallholder ...
Edmealem Temesgen Ebstu +9 more
wiley +1 more source
ABSTRACT Understanding the corrosion behavior of glass–ceramic composite materials such as Fe‐Al‐BG‐Gd2Ti2O7 as potential nuclear wasteform candidates has attracted considerable attention due to their high loading of actinide elements and fission products compared to current borosilicate glass nuclear wasteforms.
Mehrnaz Mikhchian, Andrew P. Grosvenor
wiley +1 more source

