Results 51 to 60 of about 73,557 (268)
Advanced Engineering Materials, EarlyView.In this review, the current state of light‐assisted 3D printing as it pertains to engineering musculoskeletal tissues including bone, cartilage, skeletal muscle, tendon, and ligaments is summarized. Common printing techniques, photoreactive materials, and study design choices are compiled and reviewed.
Meagan Morgan, Bin Zhang, Roger Narayan
wiley +1 more source
Micro-slurry jet for surface processing of dental ceramics
Biosurface and Biotribology, 2019 A micro-slurry jet (MSJ) was used for removing microscopic cracks and microstructural defects on surfaces of dental ceramics, in which the MSJ functioned as a wet blasting machine using mixed alumina particles and water to spray workpiece surfaces by a ...
Takashi Baba +5 more
doaj +1 more source
Advanced Engineering Materials, EarlyView.A flexure‐based variable stiffness structure is developed by integrating phase‐change modulation and adhesive interfacial locking of gallium. The design enables a wide stiffness variability, transitioning from soft, flexible behavior to rigid, load‐supporting performance.
Sungjin Kim +2 more
wiley +1 more source
Advanced Engineering Materials, EarlyView.A numerical–experimental framework is developed for characterizing multi‐matrix fiber‐reinforced polymers (MM‐FRPs) combining epoxy and polyurethane matrices. Harmonic bending tests are integrated with finite element model updating (FEMU) to simultaneously identify elastic and viscoelastic material parameters.
Rodrigo M. Dartora +4 more
wiley +1 more source
Advanced Engineering Materials, EarlyView.A simplified thermoplastic pultrusion model is developed to predict thermal fields in glass fiber/polyethylene terephthalate (GF/PET) composites with reduced computational cost. By combining effective material homogenization, validation against literature data, and Gaussian‐process‐based optimization, the study reveals how heating limits, pulling speed,
Elder Soares +3 more
wiley +1 more source
Maderas: Ciencia y Tecnología, 2018 This study shows that it is feasible to make one-layer experimental particleboards from banana chips. Mechanical properties were easily satisfied at lower dosing rates, however thickness swelling remains a problem. The addition of 1% wax to the boards
Antonios Papadopoulos
doaj
The Journal of Indian Prosthodontic SocietyAim: To evaluate and compare the mechanical and physical properties of provisional crown and bridge materials fabricated using milling, three-dimensional (3D) printing, and conventional methods. Settings and Design: This was a comparative in vitro study.
Sridevi Marothi +5 more
doaj +1 more source
Kvasný průmysl, 2020 Four new aroma hop varieties – Saaz Brilliant, Saaz Comfort, Saaz Shine and Mimosa – were registered in the Czech Republic in 2019. All of the new hop varieties have significantly higher yields than the traditional Saaz aroma variety.
Vladimír Nesvadba , Jitka Charvátová
doaj +1 more source
Advanced Engineering Materials, EarlyView.Identified through the use of statistical design of experiments and metallographic investigation, this study exposes the stochastic origins of intergranular cracks in blown powder laser beam directed energy deposition additive manufacturing of pure molybdenum. It further demonstrates a successful crack mitigation approach with direct correlation to the
Nathaniel J. Lies +2 more
wiley +1 more source
Microstructure Evolution of a VMnFeCoNi High‐Entropy Alloy After Synthesis, Swaging, and Annealing
Advanced Engineering Materials, EarlyView.The synthesis and processing (rotary swaging and annealing) of the novel VMnFeCoNi alloy is investigated, alongside the estimation of the grain size effect on hardness. Analysis of a wide grain size range of recrystallized microstructures (12–210 µm) reveals a low annealing twin density.
Aditya Srinivasan Tirunilai +6 more
wiley +1 more source