Results 81 to 90 of about 211,409 (307)
Advanced Engineering Materials, EarlyView.This study shows that superalloys used in aircraft engine disks become much more prone to deformation at high temperatures if they have been strained during manufacturing. This effect increases with the level of prior strain but eventually reaches a limit.
Fabio Machado Alves da Fonseca +9 more
wiley +1 more source
Fracture toughness characterization of thin Ti/SiC composites [PDF]
, 2011 Titanium based alloys reinforced uniaxially with silicon carbide fibres (Ti/SiC) are advanced and innovative materials for aerospace vehicles.
Ma, Wei
core
Atelier méthodologique : "Construire son introduction de thèse", par Pierre Molinier [PDF]
, 2015 L’ADT-SIC propose une réflexion collective avec Pierre Molinier, professeur en Sciences de l’Information et de la Communication à l'Université de Toulouse 2 Jean Jaurès, autour des propos introductifs de la thèse à travers un atelier qui aura lieu le ...
Bureau de l'Adt-SIC
core +2 more sources
Advanced Engineering Materials, EarlyView.Low‐voltage FIB‐SEM tomography combined with a image preprocessing pipeline improves phase contrast and enables reliable machine‐learning segmentation of conductive networks in lithium‐ion battery electrodes. Structural descriptors are extracted from segmented images, done semimanually and automated, and compared.
Lisa Beran +6 more
wiley +1 more source
Properties of nanostructured diamond-silicon carbide composites sintered by high pressure infiltration technique [PDF]
, 2004 A high-pressure silicon infiltration technique was applied to sinter diamond–SiC composites with different diamond crystal sizes. Composite samples were sintered at pressure 8 GPa and temperature 2170 K.
Dub, S. N. +8 more
core +1 more source
Simulation and Optimization Design of SiC-Based PN Betavoltaic Microbattery Using Tritium Source
Crystals, 2020 In this paper, the Monte Carlo method and numerical model are used to build the electrical model of a SiC-based betavoltaic microbattery using a 3H source, and the influences of structural parameters and the surface recombination effect on the output ...
Zhang Lin
doaj +1 more source
Foundations of Physics, 2020 AbstractThe problem of constructing maximal equiangular tight frames or SICs was raised by Zauner in 1998. Four years ago it was realized that the problem is closely connected to a major open problem in number theory. We discuss why such a connection was perhaps to be expected, and give a simplified sketch of some developments that have taken place in ...
openaire +3 more sources
Advanced Engineering Materials, EarlyView.Sol–gel‐derived ZnO–rGO hybrid nanoparticles enable Al7075 powder‐metallurgy composites to achieve concurrent gains in hardness and thermal conductivity while markedly lowering friction and wear. The hybrid architecture couples ZnO‐based load support with rGO‐assisted lamellar sliding and heat spreading, revealing a promising route toward lightweight ...
Bunyamin Aksakal +3 more
wiley +1 more source
Development Of Si02 Thin Film On singlecrystal Sic By anodic oxidation technique. [PDF]
, 2008 Anodic silicon dioxide (Si02) thin film is growth on p- and n-type silicon (Si) and p-type 4H-silicon carbide (SiC) substrate with the thickness ranging from 50-130 nm.
Cheong, Kuan Yew +2 more
core
Fractional Occupation Numbers and SIC-Scaling Methods with the Fermi-Lowdin Orbital SIC Approach [PDF]
, 2020 We derive an alternate expression for the Fermi-Lowdin Orbital Self-Interaction Correction (FLO-SIC) energy gradient and re-visit how the FLO-SIC methodology can be seen as a constrained unitary transformation acting on canonical Kohn-Sham orbitals.
Bryan, Wong +2 more
core +1 more source