Results 41 to 50 of about 843 (168)
Oxidation effects during laser cladding of aluminium with SiC/Al powders [PDF]
Journal of Materials Science, 1990 Aluminium substrates were covered with a layer of an Al-SiC powder mixture. The surface was scanned with a laser beam during which the surface was melted. The top layer of the laser tracks contained oxide plates apart from some large SiC particles. In the bottom layer a cellular network was found with aluminium cells and silicon-rich cell walls.
HEGGE, HJ, BOETJE, J, DEHOSSON, JTM
openaire +3 more sources
Production, Properties, and Applications of Surface‐Crusted Lightweight Metals in Wind Turbines
Advanced Engineering Materials, Volume 28, Issue 11, 3 June 2026.The figure describes an application of surface‐crusted lightweight metals (cellular aluminium materials) for blades in small vertical wind turbines. This application has been analyzed with regard to production technology, aerodynamic design, ecological impact, and production energy requirements.
Iva Nova, Karel Frana, Milan Jelínek
wiley +1 more source
Recent Advances in PVA‐Based Humidity Sensors: Materials Design and Future Prospects
Advanced Sustainable Systems, Volume 10, Issue 6, June 2026.Polyvinyl alcohol‐based humidity sensing materials, highlighting pristine PVA, polymer blends, and organic/inorganic composites for enhanced sensing performance. ABSTRACT Polyvinyl alcohol (PVA) and its derivatives have gained considerable attention for humidity‐sensing applications due to their hydrophilic nature, excellent film‐forming ability, and ...
Premkumar Sharad Bhosale +12 more
wiley +1 more source
Journal of the American Ceramic Society, Volume 109, Issue 6, June 2026.ABSTRACT Chemical vapor infiltration (CVI) is widely used to manufacture ceramic matrix composites, but deposition non‐uniformity and premature pore closure still limit processing time and cost. CVI operates at low pressures and in microscale pores, where non‐equilibrium gas transport develops, making common continuum assumptions unreliable.
Ege Can Ek +5 more
wiley +1 more source
Modification of Prepared (Al 2024/Alumina/Mn) Composite by Laser Surface SiC Clad Layer [PDF]
Engineering and Technology Journal, 2019 The present work shows the cladding process of silicon carbide on the substrate of prepared composite (Al 2024/Alumina/Mn) by using a laser beam (pulsed Nd-YAG). To obtain the desired results, the best laser parameters were chosen.
Marwa Juber +3 more
doaj +1 more source
Recent Developments in Deep‐Ultraviolet Flat Optics
Nanophotonics, Volume 15, Issue 10, 27 May 2026.Deep‐ultraviolet flat optics (DUVFO) is emerging as a key platform for next‐generation photonics, enabling advanced functionalities beyond conventional DUV optics. This review outlines materials, devices, and system advances, highlighting wide‐bandgap platforms, while identifying key challenges in dispersion control, characterization, and wafer‐scale ...
Omar A. M. Abdelraouf +2 more
wiley +1 more source
Neutronics Assessment of Accident-Tolerant Fuel in Advanced Power Reactor 1400 (APR1400)
Atom Indonesia, 2020 Safety and reliability are the most desirable conditions that each nuclear power plant should improve. Since the Fukushima Daiichi accident, Accident-Tolerant Fuel (ATF) has been extensively researched to improve the performance of the nuclear fuel ...
D. Hartanto +5 more
doaj +1 more source
Effect of initial coating crack on the mechanical performance of surface-coated zircaloy cladding
Nuclear Engineering and Technology, 2021 In this paper, the mechanical performance of cracked surface-coated Zircaloy cladding, which has different coating materials, coating thicknesses and initial crack lengths, has been investigated.
Ze Xu, Yulan Liu, Biao Wang
doaj +1 more source
Advances in Solid‐Phase Processing Techniques: Innovations, Applications, and Future Perspectives
Advanced Materials Technologies, Volume 11, Issue 9, 6 May 2026.Based on practical manufacturing challenges, this review examines advanced solid‐phase processing techniques that overcome the inherent limitations of conventional melting‐based and traditional solid‐phase manufacturing, enabling the production of higher‐performance components at reduced cost through process innovation and improved supply‐chain ...
Tianhao Wang
wiley +1 more source
Advanced Functional Materials for Marine Energy Utilization
Interdisciplinary Materials, Volume 5, Issue 3, Page 317-356, May 2026.Marine renewable energy is an important future clean energy supply. We construct and sort out the material system for marine energy capture and conversion, transmission, storage, and utilization for the first time. ABSTRACT Several features of marine energy, including large reserves, sustainable utilization, environmental friendliness, make it a ...
Qiang Yu +7 more
wiley +1 more source