Results 31 to 40 of about 244,799 (302)
Metals, 2022 The fuel segregation distribution sintering process, with a high fuel dosage in upper layer and a low fuel dosage in bottom layer of the sintering bed, was studied to handle uneven heat distribution problems in the conventional iron ore sintering process.
Qiangjian Gao +5 more
doaj +1 more source
CeramicsUsing spark plasma sintering technology, SiC-TiB2-TiC ceramic composites with various graphene oxide content (0.15, 0.25, 0.5 vol.%) were manufactured, and their microstructure as well as physico-mechanical and tribological properties were studied ...
Yaroslav Meleshkin +6 more
doaj +1 more source
Preparation and characterisation of inexpensive porous kaolin hollow fibre as ceramic membrane supports for gas separation application [PDF]
, 2017 Low-cost, porous ceramic kaolin-based hollow fibre membrane support (HFMS) for gas separation application was developed via phase inversion technique.
A Rahman, Mukhlis +7 more
core +1 more source
Fenmo yejin jishu, 2022 The mechanical properties of the high temperature resistant TC11 alloys prepared by spark plasma sintering (SPS) used for engine were improved by adding grapheme, the density of TC11 alloy under the different sintering parameters was studied, the ...
WU Xiao-jun
doaj +1 more source
Preparation and electrical properties of dense micro-cermets made of nickel ferrite and metallic copper [PDF]
, 2009 Dense micro-cermets made of nickel ferrites and copper micrometric particles were obtained from partial reduction under hydrogenated atmosphere at 350 C of mixed copper nickel ferrites, and sintering in nitrogen at 980 C.
Baco-Carles, Valérie +4 more
core +3 more sources
Advanced Engineering Materials, EarlyView.Powder metal processing provides scalable advantages in nanoporous (np) metal development. Mechanical alloying is used to produce unique precursors for hybrid nanopore formation by oxide reduction and dealloying. As demonstrated in np Ag, this approach improves process efficiency while promoting smaller ligaments and larger pores, both of which are ...
Mark A. Atwater, Oliver A. Fowler
wiley +1 more source
Effect of sintering temperature under high pressure in the uperconductivity for MgB2 [PDF]
, 2001 We report the effect of the sintering temperature on the superconductivity of MgB2 pellets prepared under a high pressure of 3 GPa. The superconducting properties of the non-heated MgB2 in this high pressure were poor.
Jung, C. U. +6 more
core +1 more source
Advanced Engineering Materials, EarlyView.This study demonstrates an efficient recycling route for out‐of‐spec AlSi10Mg atomized powders through compaction and arc remelting followed by suction casting. By correlating compaction load, cooling rate, and resulting microstructure, we show that intermediate pressures (50–80 kN) and rapid cooling refine dendrites, reduce porosity, and enhance ...
Mila Christy de Oliveira +4 more
wiley +1 more source
Mechanism of reduced sintering temperature of Al2O3–ZrO2 nanocomposites obtained by microwave hydrothermal synthesis [PDF]
, 2018 A novel method to obtain Al2O3–ZrO2 nanocomposites is presented. It consists of the co-precipitation step of boehmite (AlO(OH)) and ZrO2, followed by microwave hydrothermal treatment at 270 °C and 60 MPa, and by calcination at 600 °C.
Ganin, Alexey +7 more
core +1 more source
Advanced Engineering Materials, EarlyView.This study examines how several molten high‐silicon electrical steels interact with both conventional and recycled MgO–C refractories. For this, various immersion experiments are conducted. In addition to infiltration, a number of mechanisms are identified and explained that control the corrosion of the refractory material.
Lukas Neubert +7 more
wiley +1 more source