Results 51 to 60 of about 7,010 (230)

Is an Apple an Orange? A Large Language Model Benchmark for Candidate Term Extraction and Subclass Decisions Against Upper Ontologies in Engineering and Materials Science

Advanced Engineering Materials, EarlyView.
Building machine‐readable vocabularies for materials science is slow, expert‐driven work. This study benchmarks 13 large language models on two of its first steps: finding candidate terms in engineering articles and deciding where they belong in a class hierarchy.
Thomas Bjarsch, Maximilian Holland, Klaus Drechsler, Johannes Schilp   +3 more
wiley   +1 more source

Hydrogen‐Assisted Fracture of Iron‐Based Fe–Ni–Al Alloys

Advanced Engineering Materials, EarlyView.
Principal relations and fracture mechanisms of single‐phase and precipitate‐strengthened Fe–Ni–Al alloys subjected to prior electrochemical hydrogen charging are identified. The mechanisms of hydrogen effect on strength and microhardness are discussed, including hydrogen‐induced increase in microhardness and the role of hydrogen in fracture behavior ...
Nataliya Yadzhak, Olha Zvirko, Rostyslav Leshchak, Hryhoriy Nykyforchyn   +3 more
wiley   +1 more source

Strengthening Of R.C. Beams by External Steel Plate Using Bonded and Unbonded Connectors [PDF]

Engineering and Technology Journal, 2015
Structural rehabilitation represents an important aspect of the construction industry and its significance is increasing. Strengthening is the process of increasing of the existing capacity of a non-damaged structure or a structural component to a ...
Ashraf A. Alfeehan, Rana H. Alkerwei
doaj   +1 more source

Numerical Modeling and Analysis of Strengthened Steel–Concrete Composite Beams in Sagging and Hogging Moment Regions

CivilEng, 2023
Strengthening of composite beams is highly needed to upgrade the capacities of existing beams. The strengthening methods can be classified as active or passive techniques.
Ayman El-Zohairy, Suzan Mustafa, Hesham Shaaban, Hani Salim, Abbas A. Allawi   +4 more
doaj   +1 more source

Creep Properties and Deformation Mechanism of Additively Manufactured NiAl‐CrMo Composites

Advanced Engineering Materials, EarlyView.
Additively manufactured NiAl‐CrMo composites contain numerous interfaces and cell boundaries that control their creep response. At 700°C under high applied stress, creep is dominated by dislocation‐controlled power‐law mechanisms. At 800°C–900°C and lower stresses, creep is primarily diffusion‐controlled along cell boundaries.
Jan Vollhüter, Andreas Bezold, Johan Westraadt, Katharina Fiegl, Subham Chattoraj, Benjamin Wahlmann, Carolin Körner, Michael Mills, Mathias Göken, Steffen Neumeier   +9 more
wiley   +1 more source

Flexural Strengthening of Reinforced Concrete Beams Using Valid Strengthening Techniques

Archives of Civil Engineering, 2013
This study aims to evaluate the efficiency of strengthening reinforced concrete beams using some valid strengthening materials and techniques. Using concrete layer, reinforced concrete layer and steel plates are investigated in this research. Experiments
Bashandy Alaa A.
doaj   +1 more source

Microstructure, Thermal Transport, and Dry‐Sliding Tribology of Powder‐Metallurgy Al7075 Composites Reinforced With Sol–Gel‐Derived ZnO–rGO Hybrid Nanoparticles

Advanced Engineering Materials, EarlyView.
Sol–gel‐derived ZnO–rGO hybrid nanoparticles enable Al7075 powder‐metallurgy composites to achieve concurrent gains in hardness and thermal conductivity while markedly lowering friction and wear. The hybrid architecture couples ZnO‐based load support with rGO‐assisted lamellar sliding and heat spreading, revealing a promising route toward lightweight ...
Bunyamin Aksakal, Cevher Kursat Macit, Merve Ayık, Hakan Tutumlu   +3 more
wiley   +1 more source

Influence of Scan Strategies in Electron Beam Powder Bed Fusion on Solidification, Microstructure, and High‐Temperature Compressive Properties of γ′‐Strengthened Inconel 738LC

Advanced Engineering Materials, EarlyView.
Experiments and thermophysical simulations were conducted to investigate the electron beam powder bed fusion electron beam (PBF‐EB/M) process for the γ′‐strengthened nickel‐based superalloy Inconel 738LC. The results demonstrate the impact of process‐induced microstructural variations on high‐temperature mechanical behavior, providing a basis for ...
Jan Niklas Petenati, Karthik Kumar Banku, Prasanth Bondi, Ivan Zhirnov, Yangyiwei Yang, Gordon Schmidt, Jürgen Christen, Georg Hasemann, Manja Krüger, Bai‐Xiang Xu, Bilal Gökce, Silja‐Katharina Rittinghaus   +11 more
wiley   +1 more source

An Experimental Study on Strengthening of Reinforced Concrete Flexural Members using Steel Wire Mesh

Curved and Layered Structures, 2017
One of the major challenges and contemporary research in the field of structural engineering is strengthening of existing structural elements using readily available materials in the market.
Al Saadi Hamza Salim Mohammed, Mohandas Hoby P., Namasivayam Aravind   +2 more
doaj   +1 more source

External and Internal Cracking Caused by Heat Treatment in Laser Powder Bed Fusion‐Fabricated Inconel 738LC Components

Advanced Engineering Materials, EarlyView.
Manufacturing problems such as heat treatment‐induced cracking hinder the widespread application of the laser powder bed fusion (LPBF) process to superalloys. In this study, cracks in the LPBF components of Inconel 738LC superalloy are characterized after heat treatment at various temperature ranges, revealing two distinct cracking behaviors.
Kosuke Kuwabara, Masahiro Kusano, Ayako Ikeda, Toshio Osada, Makoto Watanabe   +4 more
wiley   +1 more source