Results 251 to 260 of about 4,678 (303)

Strip casting experiences at MEFOS

Scandinavian Journal of Metallurgy, 2000
Continuous casting of flat products today is a mature technique for production of steel semis with an as‐cast thickness of 200 mm. At present, the thin slab casting is developed to the extent of casting and in‐line rolling of strips with a thickness of 1–2 mm.
Ralph Nyström, Wolfgang Reichelt, Mathias Dubke   +2 more
openaire   +1 more source

Roll Casting of Clad Strip

Materials Science Forum, 2012
Roll caster to cast a three layers clad strip was invented and effect of casting conditions on the clad strip was investigated. Two vertical type twin roll casters were set at vertically tandem position to cast three layers clad strip. Roll speed, roll load (separating force), melt temperature and elements of the aluminum alloy were chosen as the ...
Toshio Haga, Ryoji Nakamura, Shinji Kumai, Hisaki Watari   +3 more
openaire   +1 more source

Direct Strip Casting of Magnesium

Zeitschrift für Metallkunde, 2004
Abstract A new interest in magnesium alloys has arisen since lightweight constructions have become more and more attractive. Products that are currently available are mostly cast, forged, and extruded. A cost-effective production of sheet metals will render new perspectives in the design of lightweight constructions [1, 2].
Heinz Palkowski, Lutz Wondraczek
openaire   +1 more source

Production of Clad Steel Strips by Twin‐Roll Strip Casting

Advanced Engineering Materials, 2015
This work presents the results obtained from the experimental investigations performed on the production of steel clad strips by vertical twin‐roll strip casting with a combination of the austenitic stainless steel 1.4301 and the carbon steel 1.1248. This production method is based on the introduction of a solid strip between the casting rolls, where ...
Michele Vidoni, Rebecca Ackermann, Silvia Richter, Gerhard Hirt   +3 more
openaire   +1 more source

Strip formation and process stability in twin roll strip casting

Steel Research, 2001
Process stability in the thin strip casting process of steel has been investigated with a laboratory pilot caster. Depending on the steel grade and the process parameters irregular process states could be observed. It has been proved experimentally that the observed behaviour is not caused by the regulation system.
Mark Badowski, Lars Hentschel, Reiner Kopp, Willi Schmitz, Dieter Senk   +4 more
openaire   +1 more source

Numerical analysis of the casting wheels of foil and strip casting machines

Materials Science and Engineering: A, 1991
Abstract Finite difference and finite element computations were employed to determine temperature and stress distributions in two casting wheel concepts. Wheel material properties and wheel geometry were varied to study their influence on the resulting casting process parameters.
E. Vogt, H. Schenk, H. Gellenbeck
openaire   +1 more source

Clad Strip Casting by a Roll Caster

Applied Mechanics and Materials, 2011
Casting of clad strip, which was one of the composite alloys, was tried using a roll caster. A vertical tandem type twin roll casters for clad strip were designed and assembled to cast the clad strip. Three layers of clad strip could be cast. The interface between the base strip and overlay strip was clear.
Toshio Haga, Ryoji Nakamura, Sinji Kumi, Hisaki Watari   +3 more
openaire   +1 more source

A Roll Caster to Cast Clad Strip

Key Engineering Materials, 2013
A tandem-type roll caster that can cast a three-layered clad strip was developed by mounting one twin roll caster on another twin roll caster. In this caster, the base strip is cast by the upper twin roll caster, and the overlay strips are cast by the lower caster. The three strips are metallurgically bonded by the lower caster. This study investigated
Haga, T., Tsuge, H., SHINJI KUMAI, Watari, H.   +3 more
openaire   +1 more source

Roll Casting of a Wire Inserted Strip

Advanced Materials Research, 2011
Casting of a wire-inserted strip was tried by a downward melt drag twin roll caster. Some numbers of wires of 0.3 mm diameter were inserted. Effects of the wire-interval, matrix alloy and melt temperature on the ability of the insertion of the wire were investigated.
Haga, T., Takahashi, K., SHINJI KUMAI, Watari, H.   +3 more
openaire   +1 more source

Direct Cast Titanium Aluminide Strip

1991
Abstract : The purpose of the Phase I research project is to demonstrate the feasibility of melting titanium alloys using Duriron's induction slag melting process and casting them into rapidly solidified strip by RIBTEC's melt overflow process. The strip might be used for SiC-Ti metal matrix composites for advanced airframe structures.
L. E. Hackman, T. A. Gaspar
openaire   +1 more source