Results 101 to 110 of about 84,785 (254)
Advanced Engineering Materials, EarlyView.It is shown that laser ablation pretreatment under oxygen‐free conditions enables copper–aluminium bonding at significantly lower deformation degrees and improved properties compared to mechanical brushing. Laser ablation further increases interface contact area and induces favourable residual stress states and microstructural compatibility ...
Khemais Barienti +11 more
wiley +1 more source
Advanced Engineering Materials, EarlyView.Low‐cycle fatigue damage in Mn–Mo–Ni reactor pressure vessel steel is examined using a combined electron backscatter diffraction and positron annihilation lifetime spectroscopy approach. The study correlates texture evolution, dislocation substructure development, and vacancy‐type defect formation across uniform, necked, and fracture regions, providing
Apu Sarkar +2 more
wiley +1 more source
Lignocellulose as Carbon Source Promotes Bacterial Synergism and Reduces Antagonism
, 2016 Lignocellulose decomposes slowly in nature because it consists of complex polymers resistant to enzymatic degradation by most organisms. Some bacteria are capable of producing cellulolytic enzymes but the way in which bacteria interact within a community
Deng, Yijie
core
Additive Gaussian Process Regression for Predictive Design of High‐Performance, Printable Silicones
Advanced Engineering Materials, EarlyView.A chemistry‐aware design framework for tuning printable polydimethylsiloxane (PDMS) for vat photopolymerization (VPP) is developed using additive Gaussian process (GP) modeling. Polymer network mechanics informs variable groupings, feasible formulation constraints, and interaction variables.
Roxana Carbonell +3 more
wiley +1 more source
Advanced Engineering Materials, EarlyView.Trace additions of Sn and Sr combined with a two‐step aging treatment are shown to enhance the microstructure and performance of Al–Zr–Sc conductor alloys. Strength and electrical conductivity increase concurrently through accelerated precipitation of fine Al3(Sc, Zr) precipitates and improved dislocation resistance, offering a cost‐effective pathway ...
Quan Shao +3 more
wiley +1 more source
Advanced Engineering Materials, EarlyView.Geometry‐driven thermal behavior in wire‐arc additive manufacturing (WAAM) influences microstructural evolution during nonequilibrium solidification of a chemically complex Fe–Cr–Nb–W–Mo–C nanocomposite system. By comparing different deposits configurations, distinct entropy–cooling rate correlations, segregation, and carbide evolution are revealed ...
Blanca Palacios +5 more
wiley +1 more source
Advanced Engineering Materials, EarlyView.Disordered (Fe50Co50)1−xPtx thin films exhibit a pronounced anomalous Nernst effect (ANE) with a strong composition dependence on both rigid and flexible substrates. The transverse thermoelectric response peaks near 22.5 at.% Pt, accompanied by enhanced αxy/σxy scaling, thermal transport, and ANE sensitivity.
Mojtaba Mohammadi +2 more
wiley +1 more source
Advanced Engineering Materials, EarlyView.This study demonstrates how optimizing laser power, scanning speed, and hatching distance in laser powder bed fusion can boost the productivity of Inconel 718 manufacturing by up to 29% while maintaining mechanical integrity. The work delivers a validated process window and cost–time analysis, offering industry‐ready guidelines for efficient additive ...
Amir Behjat +7 more
wiley +1 more source
Advanced Engineering Materials, EarlyView.Mg–Zn composites with a thickness of 0.21 mm were fabricated using roll bonding of a kirigami‐patterned Mg alloy inlay within a Zn matrix. Thermal activation following this process led to the formation of tailored intermetallic structures, which provided the composite with enhanced flexural strength.
Yaroslav Frolov +4 more
wiley +1 more source
Advanced Engineering Materials, EarlyView.Additive manufacturing provides precise control over the placement of continuous fibres within polymer matrices, enabling customised mechanical performance in composite components. This article explores processing strategies, mechanical testing, and modelling approaches for additive manufactured continuous fibre‐reinforced composites.
Cherian Thomas, Amir Hosein Sakhaei
wiley +1 more source