Results 1 to 10 of about 40,291 (284)

An investigation into the polylactic acid texturization through thermomechanical processing and the improved d33 piezoelectric outcome of the fabricated scaffolds [PDF]

Journal of Materials Research and Technology, 2021
The bio/sensors performance has been established to be significantly affected through partially or entirely alignment of nano/microfibrous in polymeric mats.
Amirhossein Farahani, Abbas Zarei-Hanzaki, Hamid Reza Abedi, Ismaeil Haririan, Mohammad Akrami, Zeynab Aalipour, Lobat Tayebi   +6 more
doaj   +2 more sources

Flow softening and recrystallization accompanied flow in AZ61 magnesium alloy during thermomechanical processing [PDF]

Heliyon
The present work deals with characterizing the recrystallization accompanied flow and high temperature softening behavior of an extruded AZ61 magnesium alloy. This was supported by conducting a set of hot compression tests at temperatures in the range of
A.R. Abbasi-Bani, A. Zarei-Hanzaki, M. G. Shabestari, H.R. Abedi   +3 more
doaj   +2 more sources

Prediction of grain structure after thermomechanical processing of U-10Mo alloy using sensitivity analysis and machine learning surrogate model. [PDF]

Sci Rep, 2022
Fu Y, Frazier WE, Choi KS, Li L, Xu Z, Joshi VV, Soulami A.   +6 more
europepmc   +3 more sources

Thermomechanical Processing for Improved Mechanical Properties of HT9 Steels. [PDF]

Materials (Basel)
Byun TS, Collins DA, Lach TG, Choi JP, Maloy SA.   +4 more
europepmc   +3 more sources

Room temperature deformation mechanisms of a Fe–Mn–Al–C steel

Journal of Materials Research and Technology, 2023
This study aims to investigate the deformation mechanisms of an austenite-based duplex Fe–Mn–Al–C steel at room-temperature through uniaxial tensile tests, strain rate sensitivity and stress relaxation analysis.
A. Moshiri, A. Zarei-Hanzaki, J. Charkhchian, A.S. Anousheh, R. Khani, H.R. Abedi   +5 more
doaj   +1 more source

On the cyclic deformation behavior and correlated damage mechanism of selective laser melted AlSi10Mg alloy holding different initial microstructures

Journal of Materials Research and Technology, 2023
The present work deals with the cyclic deformation behavior of AlSi10Mg alloy fabricated through selective laser melting. Toward this end, the printed material was heat treated and was tested through strain-controlled push–pull fatigue under different ...
F. Bathaee, A. Zarei-Hanzaki, A. Moshiri, H.R. Abedi   +3 more
doaj   +1 more source

Hot Deformation Behavior of a Ni-Based Superalloy with Suppressed Precipitation

Metals, 2021
Inconel®718 is a well-known nickel-based super-alloy used for high-temperature applications after thermomechanical processes followed by heat treatments. This work describes the evolution of the microstructure and the stresses during hot deformation of a
Franco Lizzi, Kashyap Pradeep, Aleksandar Stanojevic, Silvana Sommadossi, Maria Cecilia Poletti   +4 more
doaj   +1 more source

Improved strength and plasticity of magnesium matrix nanocomposites reinforced by carbonaceous nanoplatelets and micro-clusters

Journal of Materials Research and Technology, 2022
The uniform distribution of carbonaceous nanomaterials in a magnesium matrix composite can dramatically improve the strength without sacrificing ductility.
M. Tahaghoghi, A. Zarei-Hanzaki, M.S. Jalali, H.R. Abedi   +3 more
doaj   +1 more source

The effect of heat treatment on the room and high temperature mechanical properties of AlSi10Mg alloy fabricated by selective laser melting

Journal of Materials Research and Technology, 2023
The present work demonstrates a novel interpretation of the effect of well-known heat treatments of solutionizing (ST) and solutionizing plus aging (T6) along with a newly-developed direct aging (DA), on the microstructural evolution and corresponding ...
N. Tabatabaei, A. Zarei-Hanzaki, A. Moshiri, H.R. Abedi   +3 more
doaj   +1 more source

Stress Relaxation during Artificial Aging of an AlSi₇Cu_0.5Mg Cast Alloy

Crystals, 2022
After casting and solidification, Al cast cylinder heads undergo a sequence of heat treatments to achieve the desired material properties. This sequence comprises solution heat treatment (SHT), quenching, and artificial aging.
René Wang, Dinesh Ram, Bernhard Stauder, Ricardo Fernández Gutiérrez, Elisabetta Gariboldi, Maria Cecilia Poletti   +5 more
doaj   +1 more source