Influence of infill settings on the flexural properties of 3D printed ABS plus polymer parts in bending loading [PDF]
AUT Journal of Mechanical EngineeringOne of the most commonly used techniques in 3D printing is Fused Deposition Modeling (FDM). Despite its widespread adoption, creating functional parts with suitable mechanical properties remains a significant challenge.
Moein Moradi +3 more
doaj +1 more source
Hydrogen‐Assisted Fracture of Iron‐Based Fe–Ni–Al Alloys
Advanced Engineering Materials, EarlyView.Principal relations and fracture mechanisms of single‐phase and precipitate‐strengthened Fe–Ni–Al alloys subjected to prior electrochemical hydrogen charging are identified. The mechanisms of hydrogen effect on strength and microhardness are discussed, including hydrogen‐induced increase in microhardness and the role of hydrogen in fracture behavior ...
Nataliya Yadzhak +3 more
wiley +1 more source
Assessing Flexural Behavior of Stabilized and Reinforced Clay [PDF]
پژوهشهای زیرساختهای عمرانیIn this study, the flexural behavior of stabilized and reinforced clay was investigated. For this purpose, kaolinite, lime at weight dosages of 1%, 3%, and 5%, as well as polypropylene fibers of 6 mm and 12 mm in length, and weight contents of 0.15%, 0 ...
Mahmood Reza Abdi +2 more
doaj +1 more source
The effect of voids on the flexural fatigue properties of carbon/epoxy composites
, 2010 The role of voids in composite failures has not been well understood or been characterized. This study presents the result of an investigation aimed at examining the mechanical behaviour of unidirectional carbon fibre-reinforced polymer matrix materials ...
Suhot, Mohamed Azlan
core
Fatigue Crack Initiation and Growth in Nanocrystalline Ni at Multiple Length‐Scales
Advanced Engineering Materials, EarlyView.Overview of miniaturized in situ SEM fatigue setup and resultant fatigue crack growth data for nanocrystalline Ni. The presented study focuses on the analysis of fatigue crack growth rate (FCGR) in focused ion beam‐notched microcantilevers prepared from nanocrystalline (NC) Ni as a model material.
Igor Moravcik +7 more
wiley +1 more source
Flatwise to Upright Build Orientations under Three-Point Bending Test of Nylon 12 (PA12) Additively Manufactured by SLS. [PDF]
Polymers (Basel), 2022 Baba MN.
europepmc +1 more source
Current Status and Challenges in Data Collection for Aerospace Coatings Deposited by Plasma Spraying
Advanced Engineering Materials, EarlyView.An innovative approach has been integrated into the GRENAT project to optimize plasma spraying and coating performance. Raw materials are accelerated and melted in the plasma generated by torches, creating coatings. Monitoring sensors collect process data which are combined with ex situ characterization data.
Lila Randriamananjara +8 more
wiley +1 more source
Effect of Coremat Xi 3 Middle Layer on Flexural Performance of Glass Fibre Composites under Different Test Rates [PDF]
INCAS BulletinThis study presents experimental results from three-point bending tests conducted on two composite types reinforced with quadriaxial glass fibre fabrics, both using unsaturated polyester resin as matrix, and differing by the presence or absence of a ...
Ioana - Gabriela CHIRACU +5 more
doaj +1 more source
Analysis of the effect of bending, fatigue, erosion-corrosion and tensile stresses on HVOF coating of metallic surfaces [PDF]
, 2006 The aim of the present study was to evaluate the bending, fatigue, tensile stresses and erosion-coiTosion characteristics o f HVOF thermally sprayed Inconel-625 powder coatings when deposited on three different metallic surfaces: (a) plain stainless ...
Al Fadhli, Hussain
core
, 2015 Test setups and boundary conditions for four different experiments: A) and E) three-point bending, B) and F) four-point bending, C) and G) cantilever bending, D) and H) axial compression.
Anita Ignatius (142960) +6 more
core +1 more source