Results 81 to 90 of about 20,532,860 (296)

The effect of moisture content over the fibre saturation points on the impact strength of wood

Royal Society Open Science
The article's main aim is to assess the mechanical behaviour of linden under high-rate loadings (impact) and its change due to changes in moisture content (MC) over fibre saturation point. For assessing the mechanical properties of green wood, mainly the
Mojtaba Hassan Vand, Jan Tippner
doaj   +1 more source

Influence of TiC and TiN Ceramic Reinforcements on the Microstructure, Thermal Expansion Behavior, and Tensile Properties of Invar 36 Manufactured by Laser Powder Bed Fusion

Advanced Engineering Materials, EarlyView.
This study examines Invar composites reinforced with titanium carbide (TiC) and titanium nitride (TiN) using laser powder bed fusion (LPBF). It presents the influence of reinforcements on microstructure, tensile properties, and thermal expansion. Results show that TiC effectively strengthens Invar while maintaining low thermal expansion, whereas TiN ...
Ayodeji Nathaniel Oyedeji, Natasha Sacks, Johannes Pötschke, Björn Matthey   +3 more
wiley   +1 more source

Rapidly Solidified High‐Strength Invar 36 Prepared by Planar‐Flow Melt Spinning

Advanced Engineering Materials, EarlyView.
The Invar 36 alloy was rapidly solidified using the planar‐flow melt‐spinning technique. Ribbon samples with thicknesses ranging from 20 to 160 mm were produced. As the grain size of the ribbon decreased to sub‐micron levels, the hardness increased by more than 2 times.
Bekir Akgül, Mehmet Kul
wiley   +1 more source

Determination of Stress Intensity Factor Value for Chevron-Notched Specimens – Pilot Study

Transactions of the VŠB: Technical University of Ostrava, Civil Engineering Series, 2017
The description of material behavior is one of important information for its application in civil engineering. One area is covering fracture mechanical properties.
Sobek Jakub, Seitl Stanislav
doaj   +1 more source

A Novel Approach to Estimate the Transition Temperature via Dynamic Nanoindentation

Advanced Engineering Materials, EarlyView.
A new dynamic nanoindentation‐based method was developed that uses the stiffness ratio as an indicator of the elastic–plastic deformation contributions at different temperatures. The approach successfully identified transition temperatures in ferritic steel and distinguished them from continuously ductile austenitic steel.
Stefan Zeiler, Nikolaus Kostwein, Ronald Schnitzer, Christian Mitterer, Verena Maier‐Kiener   +4 more
wiley   +1 more source

Flatwise to Upright Build Orientations under Three-Point Bending Test of Nylon 12 (PA12) Additively Manufactured by SLS. [PDF]

Polymers (Basel), 2022
Baba MN.
europepmc   +1 more source

FastNano Liquid: An Automated Platform for Small‐Angle X‐ray Scattering‐Based Materials Discovery

Advanced Engineering Materials, EarlyView.
We present FastNano Liquid, an automated small‐ and wide‐angle X‐ray scattering platform for the combined synthesis and characterization of (nano)materials. The platform is coupled to varied reactor workflows for both in situ studies of reaction kinetics and ex situ screening of synthesis conditions to support machine learning‐guided exploration ...
Pierre‐Baptiste Flandrin, Émeline Cournède, Jens Krarup, Michael Lesa, Foyzul Hasan, Amandine Séné, Arnaud Lahouati, David Benhaiem, Jérémie‐Luc Sanchez, Simon Delacroix, Thierry Gacoin, Fabienne Testard, Damien Faivre, David Carriere, Corinne Chevallard, Olivier Taché, Mark A. Levenstein   +16 more
wiley   +1 more source

Enhancement of the Through‐Thickness Electrical Conductivity of Carbon‐Fiber‐Reinforced Plastics Using Large Graphite Particles

Advanced Engineering Materials, EarlyView.
To enhance through‐thickness conductivity without sacrificing impregnation, large spherical graphite particles are intentionally employed in a low‐viscosity resin. Unlike finer conductive fillers, these particles remain outside the fiber bundles and accumulate in resin‐rich interlaminar regions during molding.
Keito Hosoe, Yu Zhou, Shintaro Kamiyama, Takao Okada, Tomohiro Yokozeki, Ryoma Tokonami, Tatsuhiro Takahashi   +6 more
wiley   +1 more source

Effects of Hydrothermal-Chemical Treatments on Bending Performance and Physical-Mechanical Properties of Four Timber Species

BioResources
The bending behavior of four key timber species (Fraxinus chinensis, teak, rubberwood, and Pinus yunnanensis) was evaluated under hydrothermal-chemical treatments. Controlled experiments at varying moisture contents (20 to 60%), temperatures (100 to 140 °
Huajie Shen, Caixia Bai, Fengwu Zhang, Yue Sun, Xinzhen Zhuo, Rongfeng Ding, Donghai Huang, Yushan Yang, Jian Qiu   +8 more
doaj  

Estimation of Post-Cracking Dissipation Capabilities of Fiber Reinforced Concretes in Three Point Bending Test Monitored with Application of Digital Image Correlation System. [PDF]

Materials (Basel), 2021
Trinh-Duc D, Piotrowski A, Ajdukiewicz C, Woyciechowski P, Gajewski M.   +4 more
europepmc   +1 more source