Results 91 to 100 of about 355,851 (216)

The role of microstructure in the stress relaxation and tempering of laser clad Ti-6Al-4V [PDF]

, 2014
In this work a heat treatment procedure was performed on laser clad Ti-6Al-4V, which resulted in a reduction of tensile residual stresses in the clad samples as well and a decrease in the hardness of the clad layer with an increasing heat treatment time.
V Luzin (9878051), Ryan Cottam (19098557), Milan Brandt (18029095), Edwin Mayes (19970466), Qianchu Liu (19970271), James Wang (510186), Yat Choy Wong (16878670)   +6 more
core   +3 more sources

Low Cycle Repetitive Loading of Ti‐6Al‐4V‐Epoxy Composite Lattice Structures for Enhanced Energy Dissipation and Damage Tolerance

Advanced Engineering Materials, Volume 28, Issue 14, 22 July 2026.
Composite Ti–6Al–4V–epoxy lattice structures are additively manufactured and epoxy infiltrated for cyclic loading. At low lattice volume fractions, hybridization produces synergistic gains in stiffness and energy dissipation. At higher volume fractions, synergy diminishes, although composites still exceed metallic lattices in specific energy ...
Joey Tallon, Jordan Noronha, Justin Dirrenberger, Andrey Molotnikov   +3 more
wiley   +1 more source

Microstructure evolution and mechanical properties of selective laser melted Ti-6Al-4V [PDF]

, 2014
Selective laser melting (SLM) has been shown to be an attractive manufacturing route for the production of α/β titanium alloys, and in particular Ti-6Al-4V.
Marco Simonelli (3722434)
core  

Robust Spot Melting by 3D Spot Arrangements in Electron Beam Powder Bed Fusion

Advanced Engineering Materials, Volume 28, Issue 13, 8 July 2026.
This work proposes an approach to replace separately melted contours for spot melting in electron beam powder fusion. Adapting the spot arrangements close to the contour combined with stacking yields a comparable surface quality without the inherent challenges of separate contours, as demonstrated, by electron optical images and roughness measurements.
Tobias Kupfer, Lukas Spano, Sebastian Pohl, Carolin Körner, Matthias Markl   +4 more
wiley   +1 more source

Corrosion and Tensile Behaviors of Ti-4Al-2V-1Mo-1Fe and Ti-6Al-4V Titanium Alloys

Metals, 2019
X-ray diffraction (XRD), scanning electron microscope (SEM), immersion, electrochemical, and tensile tests were employed to analyze the phase constitution, microstructure, corrosion behaviors, and tensile properties of a Ti-6Al-4V alloy and a newly ...
Yanxin Qiao, Daokui Xu, Shuo Wang, Yingjie Ma, Jian Chen, Yuxin Wang, Huiling Zhou   +6 more
doaj   +1 more source

Enhanced Strength and Corrosion Resistance of Ti‐13Nb‐12Ta‐10Zr‐4Sn Alloy by Aging Treatment

Advanced Engineering Materials, Volume 28, Issue 13, 8 July 2026.
This work systematically investigates the effect of aging treatment on mechanical properties and corrosion behavior of vacuum arc‐melted Ti‐13Nb‐12Ta‐10Zr‐4Sn alloy. Owing to the increased α″ martensite, strength and corrosion resistance were significantly enhanced by aging treatment.
Yuhua Li, Rong Zhao, Qian Zhang, Haojie Wang, Yujing Liu, Lai‐Chang Zhang   +5 more
wiley   +1 more source

Microstructure of Ti-6Al-4V produced by selective laser melting [PDF]

, 2012
Ti-6Al-4V is the most widely used titanium alloy. Manufacturing of Ti-6Al-4V components using novel additive processing techniques such as selective laser melting is of great interest.
Yau Tse (1249800), Christopher Tuck (4751376), Marco Simonelli (3722434)   +2 more
core   +3 more sources

Friction–wear behaviors and microstructure of AlTiVCrNb lightweight refractory high-entropy alloy coating prepared by laser cladding on Ti–6Al–4V substrate

Journal of Materials Research and Technology
To enhance the friction and wear properties of Ti–6Al–4V, the AlTiVCrNb lightweight refractory high entropy alloy coating was applied to a Ti–6Al–4V substrate by laser cladding.
Xuanhong Hao, Hongxi Liu, Xiaowei Zhang, Lin Chen, Yueyi Wang, Chen Yang, Yaxia Liu   +6 more
doaj   +1 more source

The effect of SLM process parameters on density, hardness, tensile strength and surface quality of Ti-6Al-4V

Additive Manufacturing, 2019
In this paper, we printed Ti-6Al-4V SLM parts based on Taguchi design of experiment and related standards to measure and compare hardness with different mechanical properties that were obtained in our previous research such as density, strength ...
A. Khorasani, I. Gibson, U. Awan, A. Ghaderi   +3 more
semanticscholar   +1 more source

Direct Metal Deposition of Graphene–Ti28Nb35.4Zr Matrix Composites With Enhanced Mechanical, Corrosion, and Biocompatibility Properties for Bone Implants

Advanced Engineering Materials, Volume 28, Issue 13, 8 July 2026.
Graphene nanoplatelet (0.1 wt.%) reinforcement significantly enhances the performance of β Ti‐28Nb‐35.4Zr alloy. Grain refinement, reduced water contact angle, and improved surface characteristics promote osteoblast adhesion and complete surface coverage after 7 days.
Khurram Munir, Jixing Lin, Yuncang Li, Li Zhu, Paul F. A. Wright, Cuie Wen   +5 more
wiley   +1 more source