Results 71 to 80 of about 66,854 (228)
Energy and force analysis of Ti-6Al-4V linear friction welds for computational modeling input and validation data [PDF]
, 2014 The linear friction welding (LFW) process is finding increasing use as a manufacturing technology for the production of titanium alloy Ti-6Al-4V aerospace components.
A. Chamanfar +18 more
core +1 more source
Journal of Prosthodontics, EarlyView.Abstract Purpose To assess the impact of anodization and instrumentation on titanium abutment surface characteristics (surface roughness and wettability) and biofilm formation (viability and mass). Materials and Methods Titanium discs were obtained from pre‐milled abutment blanks made of titanium‐6aluminum‐7niobium alloy.
Weiqing Liu +4 more
wiley +1 more source
Corrosion and Tensile Behaviors of Ti-4Al-2V-1Mo-1Fe and Ti-6Al-4V Titanium Alloys
Metals, 2019 X-ray diffraction (XRD), scanning electron microscope (SEM), immersion, electrochemical, and tensile tests were employed to analyze the phase constitution, microstructure, corrosion behaviors, and tensile properties of a Ti-6Al-4V alloy and a newly ...
Yanxin Qiao +6 more
doaj +1 more source
Selected fretting-wear-resistant coatings for titanium - 6-percent-aluminum - 4-percent-vanadium alloy [PDF]
A titanium - 6-percent-aluminum - 4-percent-vanadium alloy (Ti-6Al-4V) was subjected to fretting-wear exposures against uncoated Ti-6Al-4V as a baseline and against various coatings and surface treatments applied to Ti-6Al-4V.
Bill, R. C.
core +1 more source
Investigation in the microstructure formation of titanium products obtained by additive manufacturing [PDF]
, 2011 The regularities in the microstructure and phase composition of the 3D printed commercially pure titanium and Ti-6Al-4V titanium alloy specimens are studied using optical and transmission electron microscopes as well as X-ray ...
Мартынов, С. А. +1 more
core +1 more source
JOR SPINE, Volume 9, Issue 2, June 2026.Spine implant development follows a regulated, iterative pathway from clinical need and design through material selection, prototyping, preclinical validation, and regulatory approval to post‐market surveillance. Biomechanical evaluation and risk‐based frameworks integrate across all stages, ensuring safe, effective translation from concept to clinical
Amit Benady +5 more
wiley +1 more source
Journal of Materials Research and TechnologyTo enhance the friction and wear properties of Ti–6Al–4V, the AlTiVCrNb lightweight refractory high entropy alloy coating was applied to a Ti–6Al–4V substrate by laser cladding.
Xuanhong Hao +6 more
doaj +1 more source
Wear Behavior of Low-Cost, Lightweight TiC/Ti-6Al-4V Composite Under Fretting: Effectiveness of Solid-Film Lubricant Counterparts [PDF]
The wear behavior of low-cost, lightweight 10-wt% TiC-particulate-reinforced Ti-6Al-4V matrix composite (TiC/Ti- 6Al-4V) was examined under fretting at 296, 423, and 523 K in air.
Andrews, Rodney +7 more
core +1 more source
Surface engineering of Ti-6Al-4V by nitriding and powder alloying using a CW CO2 laser [PDF]
, 2008 A comparison has been made of the laser processing of Ti-6Al-4V (IMI-318) alloy by (a) nitriding under a dilute atmosphere, (b) preplaced 6 µm SiC powder and (c) a combination of (a) and (b). At least six laser tracks were overlapped.
Baker, T.N., Selamat, M.S.
core +1 more source
Fatigue &Fracture of Engineering Materials &Structures, Volume 49, Issue 6, Page 2352-2362, June 2026.ABSTRACT The milling process significantly influences the surface integrity of metallic components through machining induced near‐surface residual stresses. Modern hybrid machining processes, such as ultrasonic‐assisted milling (USAM), offer the potential to induce beneficial near‐surface compressive residual stresses compared to the near‐surface ...
Lorenz Engelking +5 more
wiley +1 more source