Results 51 to 60 of about 353 (132)

TiAlN-Beschichtungen mittels hochenergetischer Kathodenzerstaeubung

open access: yes, 2020
Hochenergetische Plasmen stellen nach aktuellen Erkenntnissen ein vielversprechendes tribologisches Eigenschaftsprofil für nitridische Hartstoffschichten und deren Anwendungen dar. Jedoch resultiert aus der gesteigerten Ionisationsrate ein hohes Niveau an Druckeigenspannungen in TiAlN‐Dünnschichten (σTiAlN ∼ –6000 MPa), welches die Haftung zwischen ...
Tillmann, Wolfgang   +2 more
openaire   +2 more sources

Industrial‐Grade Structural Coloration with Robust and Vivid TiON‐Based Structures

open access: yesAdvanced Optical Materials, Volume 14, Issue 4, 27 January 2026.
This study presents TiON‐based Fabry–Perot cavities as a robust strategy for structural coloration. By substituting the metal top layer with TiON, the structures achieve vivid, tunable colors and resist oxidation, abrasion, and humidity. Long‐term testing demonstrates stable optical absorption and minimal chromatic drift, highlighting TiON's ...
Md. Abdur Rahman   +8 more
wiley   +1 more source

Design and Analysis for Cryogenic Liquid and High‐Pressure Compressed Gaseous Hydrogen Storage Vessels: A Review

open access: yesInternational Journal of Energy Research, Volume 2026, Issue 1, 2026.
Cryogenic liquid hydrogen (LH2) and high‐pressure compressed gaseous hydrogen (CGH2) vessels are the core technologies for large‐scale hydrogen storage. This review systematically examines their design challenges and failure mechanisms under extreme cryogenic and high‐pressure conditions. For LH2 vessels, recent advances in thermal insulation, boil‐off
Mengfan Wei   +7 more
wiley   +1 more source

Evaluation of wear resistance of CrN, CrAlN, and TiAlN coatings deposited by multi-arc ion plating on spinning die of Cr12MoV

open access: yesMaterials Research Express
This study successfully deposited CrN, CrAlN, and TiAlN coatings on the surface of Cr12MoV substrate using multi-arc ion plating (MAIP). The influence of phase composition and surface morphology on the hardness, adhesion strength, friction performance ...
Rongchuan Lin   +5 more
doaj   +1 more source

Multimodal Data Fusion and Cross‐Scenario Transfer Learning for Condition Monitoring of CNC Machine Tools Under Low Sample Conditions

open access: yesStructural Control and Health Monitoring, Volume 2026, Issue 1, 2026.
Precise monitoring of tool wear state is critical for the machining quality and production efficiency of CNC machine tools, yet industrial practice is constrained by insufficient fusion of multisource heterogeneous signals, cross‐condition distribution drift, and scarcity of labeled samples.
Rong Nie   +3 more
wiley   +1 more source

Mechanical and tribological properties enhancement of heat treated AISI 4340 steel by using a TiN/TiAlN multilayer coating system

open access: yesRevista Facultad de Ingeniería Universidad de Antioquia, 2014
TiN/TiAlN (titanium nitride/titanium aluminum nitride) multilayer were deposited by d.c. reactive magnetron sputtering using titanium and aluminum targets with 10 cm in diameter and 99.9% purity in an argon/nitrogen (Ar/ N) atmosphere, applying a ...
Gilberto Bejarano   +2 more
doaj   +1 more source

Deformation Behavior of Optical Ceramic Nanomultilayers: The Role of Aperiodicity

open access: yesAdvanced Engineering Materials, Volume 27, Issue 21, November 2025.
Ceramic nanomultilayers demonstrate optical and mechanical behavior tunability through aperiodicity. Within the studied systems, optically optimized coatings exhibit an average ultraviolet, visible, and near‐infrared spectral transmittance above 90%.
Danielle E. White   +5 more
wiley   +1 more source

Hard Machining of Inconel 690 Using Minimum Quantity Nanoparticle‐Enriched Vegetable Oils: A Sustainable Approach

open access: yesEngineering Reports, Volume 7, Issue 10, October 2025.
This study explores alumina and silica nanoparticle‐enriched soybean oil for sustainable machining of Inconel 690. Alumina‐based nanofluid reduced surface roughness, force, temperature, and tool wear significantly. RSM‐GA optimization validated with 3.04% error highlights its eco‐efficiency, tool life enhancement, and potential for greener ...
Jasgurpreet Singh Chohan   +8 more
wiley   +1 more source

Cutting Performance and Tool Wear of AlCrN- and TiAlN-Coated Carbide Tools during Milling of Tantalum–Tungsten Alloy

open access: yesMachines
Tantalum–tungsten alloys have been widely used in different industrial sectors—for example, in chemical, medical, aerospace, and military equipment. However, they are usually difficult to cut because of the large cutting force, rapid tool wear, and poor ...
Jiahao Wang   +4 more
doaj   +1 more source

Ceramics Surface Design by Laser Texturing: A Review on Structures and Functionalities

open access: yesAdvanced Materials Interfaces, Volume 12, Issue 17, September 8, 2025.
Laser surface texturing (LST) is a huge source for innovation in ceramics, as its versatility allows a swift production of very distinct functionalities for attaining high performances in several fields. This function‐oriented review gathers highly relevant applications of laser surface textured ceramics, from optical, thermal, electronic ...
Edna Silva   +2 more
wiley   +1 more source

Home - About - Disclaimer - Privacy