Results 91 to 100 of about 8,484,552 (340)
Dynamic Precipitation during High‐Pressure Torsion of a Magnesium–Manganese Alloy
Advanced Engineering Materials, EarlyView.An ultrafine‐grained alloy is produced by high‐pressure torsion of solutionized Mg–1.35 wt% Mn. Precipitation of nanometer‐scale Mn particles during deformation provides pinning sites. This prevents the formation of a bimodal grain structure and results in a finer grain size than for pure Mg.
Julian M. Rosalie, Anton Hohenwarter
wiley +1 more source
Precise asymptotics: robust stochastic volatility models
, 2018 We present a new methodology to analyze large classes of (classical and rough) stochastic volatility models, with special regard to short-time and small noise formulae for option prices.
Friz, Peter K. +2 more
core +2 more sources
Robotized FSW – Evolution of forces and torque with nonlinear welds [PDF]
, 2014 The main purpose of the article is to study the evolution of the welding forces and torque with non-straight welding path. The main studies performed on forces and torque are usually done on plane straight welding path when the processing parameter are ...
ABBA, Gabriel +6 more
core +2 more sources
Advanced Engineering Materials, EarlyView.Freeze‐drying of layered silicate is the key to get coatings with superior gas barrier. Freeze‐drying of layered silicates modified with dodecylamine (DDA) is a highly effective technique for the preparation of barrier pigments that significantly mitigate the permeation of oxygen, water vapor, and hydrogen through polymer films containing these ...
Joshua Lommes +4 more
wiley +1 more source
Applied Sciences, 2020 Pocket milling has been regarded as one of the most widely used operations in machining. The surface quality of the machined pockets is an essential aspect of any engineering and medical applications.
Basem M. A. Abdo +2 more
doaj +1 more source
Achieving Effective Innovation Based On TRIZ Technological Evolution [PDF]
, 2009 Organised by: Cranfield UniversityThis paper outlines the conception of effective innovation and discusses the method to achieve it. Effective Innovation is constrained on the path of technological evolution so that the corresponding path must be ...
Cao, G. Z., Sun, J. G., Tan, R. H.
core
Nonstabilized Nielsen coincidence invariants and Hopf--Ganea homomorphisms
, 2006 In classical fixed point and coincidence theory the notion of Nielsen numbers has proved to be extremely fruitful. We extend it to pairs (f_1,f_2) of maps between manifolds of arbitrary dimensions, using nonstabilized normal bordism theory as our main ...
Bogatyĭ +13 more
core +3 more sources
Influence of the Trochoidal Tool Path on Quality Surface of Groove Walls
Advances in Science and Technology Research Journal, 2019 The article presents the results of machining materials in hardened state. In the paper, different trochoidal tool paths are compared with each other and with the conventional milling.
Kamil Waszczuk +4 more
semanticscholar +1 more source
Advanced Engineering Materials, EarlyView.An idea of designing novel sensors is proposed by creating appropriate Schottky barriers and vacancies between isomorphous Core‐CuOii/ Shell‐CuOi secondary microspheres and enhancing catalytic and spill‐over effects, and electronegativity via spontaneous biphasic separation, self‐assembly, and trace‐Ni‐doping.
Bala Ismail Adamu +8 more
wiley +1 more source
An Analytical Decoupled Corner Smoothing Method for Five-Axis Linear Tool Paths
IEEE Access, 2019 Nowadays, the tool path in five-axis machining is usually described with linear segments. Tangential and curvature discontinuities of the linear tool path lead to poor machining efficiency and quality.
Xin Zhao +4 more
doaj +1 more source