Results 221 to 230 of about 859,127 (297)
Some of the next articles are maybe not open access.
Simulation of solidification microstructure in twin-roll casting strip
Computational Materials Science, 2010The twin-roll strip casting is regarded as the most prospective technology of near-net-shape casting. The control of the grain structure is of primary importance in twin-roll strip casting because the solidification microstructure has great influence on the quality and mechanical properties of strips.
Bo Wang, Jie Yu Zhang
exaly +2 more sources
A medium-Mn steel processed by novel twin-roll strip casting route
Materials Science and Technology, 2019A medium-Mn steel (Fe–0.3C–4Mn–1.82Al–0.6Si wt-%) was produced by a novel processing route involving twin-roll strip casting, hot rolling and intercritical annealing (IA). Macrosegregation was absent in the as-cast strip.
R D K Misra +2 more
exaly +2 more sources
Dynamic Modeling of Twin-Roll Steel Strip Casting
Volume 2: Mechatronics; Mechatronics and Controls in Advanced Manufacturing; Modeling and Control of Automotive Systems and Combustion Engines; Modeling and Validation; Motion and Vibration Control Applications; Multi-Agent and Networked Systems; Path Planning and Motion Control; Robot Manipulators; Sensors and Actuators; Tracking Control Systems; Uncertain Systems and Robustness; Unmanned, Ground and Surface Robotics; Vehicle Dynamic Controls; Vehicle Dynamics and Traffic Control, 2016 We consider the problem of dynamic coupling between the rapid thermal solidification and mechanical compression of steel in twin-roll steel strip casting. In traditional steel casting, molten steel is first solidified into thick slabs and then compressed via a series of rollers to create thin sheets of steel.
Florian Browne, George Chiu, Neera Jain
openaire +2 more sources
Twin-roll strip casting of advanced metallic materials
Science China Technological Sciences, 2021ChenYang Zhu, Jie Zeng, WanLin Wang
openaire +2 more sources
The International Journal of Advanced Manufacturing Technology, 2022
Dongpo Xuan +6 more
openaire +2 more sources
Dongpo Xuan +6 more
openaire +2 more sources
Philosophical Magazine A, 2023
The twin-roll strip casting (TRSC) process was introduced because of its sub-rapid solidification characteristics, and the element segregation and ageing precipitation of the Cu-6Ni-1.4Si-0.1Cr alloy were studied.
G. Cao +4 more
semanticscholar +1 more source
The twin-roll strip casting (TRSC) process was introduced because of its sub-rapid solidification characteristics, and the element segregation and ageing precipitation of the Cu-6Ni-1.4Si-0.1Cr alloy were studied.
G. Cao +4 more
semanticscholar +1 more source
The twin-roll strip casting of magnesium
JOM, 2004Commonwealth Scientific & Industrial Research Organization has been working since 2000 to develop twin-roll strip casting of magnesium alloy. The primary objective was to significantly reduce the manufacturing cost of the magnesium sheet through the twin-roll casting process.
D. Liang, C. B. Cowley
openaire +1 more source
Twin roll casting of aluminum alloy strips
Journal of Materials Processing Technology, 2004Abstract Two kinds of twin roll caster for aluminum alloys were devised in the present study. Vertical type was adopted. The strip, which was thinner than 3 mm, could be cast at speeds higher than 60 m/min. Aluminum alloy, which freezing zone is very wide like A5182, could be cast using the twin roll caster of the present study at speeds up to 150 m ...
Toshio Haga +3 more
openaire +1 more source
, 2021
Fe-based amorphous alloys are characteristic of high saturation magnetization, low coercivity, and low core loss, which holds a grand promise for several engineering applications, such as soft magnetic, corrosion-resistant and wear-resistant coatings ...
C. Liu +5 more
semanticscholar +1 more source
Fe-based amorphous alloys are characteristic of high saturation magnetization, low coercivity, and low core loss, which holds a grand promise for several engineering applications, such as soft magnetic, corrosion-resistant and wear-resistant coatings ...
C. Liu +5 more
semanticscholar +1 more source