Results 241 to 250 of about 12,750 (288)

Production of Clad Steel Strips by Twin‐Roll Strip Casting

Advanced Engineering Materials, 2015
This work presents the results obtained from the experimental investigations performed on the production of steel clad strips by vertical twin‐roll strip casting with a combination of the austenitic stainless steel 1.4301 and the carbon steel 1.1248. This production method is based on the introduction of a solid strip between the casting rolls, where ...
Michele Vidoni, Rebecca Ackermann, Silvia Richter, Gerhard Hirt   +3 more
openaire   +1 more source

Strip formation and process stability in twin roll strip casting

Steel Research, 2001
Process stability in the thin strip casting process of steel has been investigated with a laboratory pilot caster. Depending on the steel grade and the process parameters irregular process states could be observed. It has been proved experimentally that the observed behaviour is not caused by the regulation system.
Mark Badowski, Lars Hentschel, Reiner Kopp, Willi Schmitz, Dieter Senk   +4 more
openaire   +1 more source

Twin-roll casting of aluminum–steel clad strips

Journal of Manufacturing Processes, 2013
Abstract The results of experiments on twin-roll casting of aluminum–steel clad strips are presented. For the first time this energy-saving production technology for a clad material of this metals combination was implemented. Besides the experimental equipment and processing details, the results of metallographic, electron microprobe and transmission
Olexandr Grydin, Gregory Gerstein, Florian Nürnberger, Mirko Schaper, Valentyn Danchenko   +4 more
openaire   +1 more source

Clad Strip Casting Using a Twin Roll Casters

Advanced Materials Research, 2011
The three layers clad strip was fabricated by a vertical type tandem twin roll caster for clad strip (VTTCC). The effect of the casting conditions of the base strip and the overlay strip on the interface between the base strip and the overlay strip was investigated. The temperature of the molten metal and roll-load were investigated casting conditions.
Ryoji Nakamura, Toshio Haga, H. Tsuge, S. Kumai, H. Watari   +4 more
openaire   +1 more source

Vertical Twin-Roll Strip Casting of Steel

2015
Vertical strip casting enables the near-net-shape production of hot rolled steel strip in a compact process. In less than half a second, the liquid steel melt solidifies in contact with the casting rolls to a one to five millimetres thin strip. Since the strip casting process combines casting and rolling in one single process, slab re-heating and ...
Markus Daamen, Michele Vidoni, Gerhard Hirt   +2 more
openaire   +1 more source

Twin roll strip casting of low carbon steels

Ironmaking & Steelmaking, 2000
Strip casting of low carbon steels has been investigated using a laboratory twin roll machine with copper rolls. The following grades have been studied: a deep drawing low carbon (LC) steel, a LC steel with titanium addition, and a high strength low alloy (HSLA) grade.
A. Girgensohn, A.R. Büchner
openaire   +1 more source

Dynamic Modeling of Twin-Roll Steel Strip Casting

Volume 2: Mechatronics; Mechatronics and Controls in Advanced Manufacturing; Modeling and Control of Automotive Systems and Combustion Engines; Modeling and Validation; Motion and Vibration Control Applications; Multi-Agent and Networked Systems; Path Planning and Motion Control; Robot Manipulators; Sensors and Actuators; Tracking Control Systems; Uncertain Systems and Robustness; Unmanned, Ground and Surface Robotics; Vehicle Dynamic Controls; Vehicle Dynamics and Traffic Control, 2016
We consider the problem of dynamic coupling between the rapid thermal solidification and mechanical compression of steel in twin-roll steel strip casting. In traditional steel casting, molten steel is first solidified into thick slabs and then compressed via a series of rollers to create thin sheets of steel.
Florian Browne, George Chiu, Neera Jain
openaire   +1 more source

A twin-roll caster to cast clad strip

Journal of Materials Processing Technology, 2003
Abstract A single-roll caster and two kinds of twin-roll casters to cast clad strips were designed and assembled. One of twin-roll casters was suitable for clad strip casting. This twin-roll caster can cast clad strips of aluminum alloys at the speed of 20 m/min. The thickness of the clad strip is about 2.0 mm.
T Haga, S Suzuki
openaire   +1 more source

Computer modelling for thin strip twin-roll casting

Steel in Translation, 2017
In twin-roll casting, the influence of the heat-transfer rate at the metal–mold boundary on the thickness and the proportion of solidifying metal at the exit from the water-cooled roller mold is analyzed. The corresponding analytical curves are plotted for the production of moderate-carbon and stainless steel strip (thickness 1–6 mm).
V. L. Naidek, N. I. Tarasevich, I. V. Korniets, I. N. Tarasevich   +3 more
openaire   +1 more source

Thin strip quality obtained in twin-roll casting

International Journal of Cast Metals Research, 1996
Ferrous alloy strips of width 150 mm and thickness 150–300 μm were obtained by rapidly cooling from the molten state at ∼ 105 Ks−1 with the pressing force of the rolls during casting 1.5 kN mm−1 an...
openaire   +1 more source