Results 41 to 50 of about 1,560 (287)

Self‐Sintering Ionogel Binder for Flexible, Recyclable, and Healable Printed Giant Magnetoresistive Sensors

Advanced Functional Materials, EarlyView.
ABSTRACT Electronic waste has emerged as a major environmental challenge, driven by the massive consumption and a limited lifetime of modern electronic devices, stimulating the development of sustainable electronics. Here, an all‐biomaterial gelatin‐choline‐citric acid ([Ch][CA]) ionogel is developed as an active binder to realize self‐sintered ...
Lin Guo, Xiaotao Wang, Guannan Mu, Proloy Taran Das, Igor Veremchuk, Conrad Schubert, Aaron D. Cross, Yevhen Zabila, Xuan Peng, Larysa Baraban, Denys Makarov   +10 more
wiley   +1 more source

Methods for estimation of the vacuum status in vacuum circuit breakers [PDF]

, 1999
In this paper several methods are described for the estimation of the pressure inside vacuum interrupters which have been in operation for many years.
Bouwmeester, C.E., Damstra, G.C., Gruntjes, R.J.B., Merck, W.F.H.   +3 more
core   +1 more source

Dispensing Volumetric Additive Manufacturing

Advanced Functional Materials, EarlyView.
Dispensing volumetric additive manufacturing (DVAM) prints 3D structures inside a photocurable resin droplet suspended from the tip of a glass pipette, enabling sequential printing without resin vats or manual part removal. Real‐time droplet profiling and ray‐tracing‐based correction compensate for optical distortion at the curved resin‐air interface ...
Hongryung Jeon, Yunsoo Lee, Seobin Park, Kyung‐Hwan Kim, Junyoung Seo, Im Doo Jung   +5 more
wiley   +1 more source

Constructing Ionic Fast Diffusion Channels on LiNi0.5Mn1.5O4 for Lithium‐Ion Batteries

Advanced Functional Materials, EarlyView.
A dual‐modification strategy is developed for LNMO cathode, where bulk Ti doping stabilizes the oxygen framework and simultaneously drives the in situ formation of LaTi2O6 nano‐islands as ion diffusion channels on (111) surfaces, enabling high‐rate capacity (∼100 mAh g−1 at 30 C) and excellent cycling retention (87.8% after 1000 cycles).
Xinyi Zhang, Sicheng Wu, Xuzhao Liu, Haocheng Guo, Jian Peng, Xia Huang, Xiaobo Zhu, Yuhui Ge, Haochen Lu, Shuhao Wang, Lianzhou Wang   +10 more
wiley   +1 more source

Design and Experimental Testing of a Moving Coil Actuator with Compensation Coils

CSEE Journal of Power and Energy Systems
Hydrogen-powered electric aircraft have attracted significant interests aiming to achieve decarbonization targets. Onboard DC electric networks are facing great challenges in DC fault protection requirements.
Boyuan Yin, Xianwu Zeng, John Frederick Eastham, Emelie Nilsson, Jean-francois Rouquette, Jean Rivenc, Ludovic Ybanez, Xiaoze Pei   +7 more
doaj   +1 more source

Engineering Intelligent Graphene Oxide‐Cellulose Membranes: Suppressing Thermal Runaway for a Safer Aqueous Zinc‐Ion Batteries

Advanced Functional Materials, EarlyView.
A novel thermos‐responsive hydroxypropyl cellulose/graphene oxide (HPC/GO) composite membrane is fabricated for reversible temperature‐gated ion transport in aqueous zinc‐ion batteries. Enabled by LCST‐driven structural transition, unimpeded ion diffusion at room temperature delivers high capacity, while elevated temperature suppresses transport; full ...
Xueli Bi, Kou Yang, Shushen Zheng, Juncheng Wang, Meng Li, Zhenzhen Wu, Yulin Zhong, Daria V. Andreeva, Kostya S. Novoselov, Shanqing Zhang   +9 more
wiley   +1 more source

Vacuum Arc Ion Flux From Vacuum Interrupter Contact Gap [PDF]

, 2017
Dielectric properties of vacuum interrupters are influenced by metal vapour deposition on the inner ceramic surfaces. Therefore these surfaces are partly protected by shield electrodes.
Kurrat, M.
core   +1 more source

Discharge characteristics for various discharge patterns under negative lightning impulse voltage in vacuum [PDF]

, 2016
In order to develop higher voltage vacuum interrupters (VIs), electrical insulation performances in vacuum should be improved. The discharge in VI has various and complex patterns, such as breakdown in vacuum gap and surface flashover on a solid ...
66956, 66957, 66958, 66959, 66960, 66961, Hayakawa, Naoki, Kimura, Toshinori, Kojima, Hiroki, Kong, Fei, Nakano, Yusuke, Tsukima, Mitsuru   +11 more
core   +1 more source

A Personalized, 3D Printed Polymeric Device for the Prevention of Post‐Myocardial Infarction Cardiac Remodeling

Advanced Healthcare Materials, EarlyView.
Myocardial infarction often leads to pathological remodelling and ventricular dilatation, key features of HFrEF. This study introduces a personalized, 3D‐printed cardiac restraint device (CARD) printed using rationally designed inks displaying the requested printability and mechanical properties.
Nicola Mansour, Daniel Cohn, Ishita Sarkar, Raja Alamore, Kareem Abd Rbo, Offer Amir, Dean Nachman   +6 more
wiley   +1 more source

Flash Assembloids: A Rapid Biofabrication of a Platform for Modeling Early Glioblastoma Invasion at the Glioblastoma–Brain Organoid Interfaces

Advanced Healthcare Materials, EarlyView.
This study presents a bioengineered assembloid (ASM) system combining glioblastoma (GBM) cells in oxidized alginate (OA) microgels with dorsal organoids (DOs). This model simulates brain tumor‐host interactions, revealing enhanced GBM invasion, altered gene expression, and aggressive infiltration patterns, demonstrating ASM as a valuable platform for ...
Chao Liang, Henry Robert Howard, Shihui Chen, Won‐Young Choi, Summer Cao, Arthur Chien, Kevin Zou, Michael Kassiou, Fabien Delerue, Ho Sang Jung, Yeonju Park, Young Mee Jung, Yong‐Dae Kwon, Karrie M. Kiang, Gilberto Ka‐Kit Leung, Ryohichi Sugimura, Ann‐Na Cho, Sang Jin Lee   +17 more
wiley   +1 more source