Results 51 to 60 of about 475,553 (315)
Effect of Particle Concentration on the Pressure Signal of the Oil Pulsation Flow Based on the Wavelet Packet [PDF]
Iranian Journal of Chemistry & Chemical EngineeringThe turbulence characteristics of the oil pulsation flow may be influenced by the concentration of particles. In this research, an NI PXI data acquisition system is utilized to experimentally analyze the flow pressure signal of the oil pulsation ...
Chen Bin, Ge Liu
doaj +1 more source
Mass loading effects on vibrated ring and shell structures [PDF]
, 1968 Efficient methods for predicting the effects of attached masses on the vibration characteristics of ring and shell structures have been developed and substantiated with experimental ...
Lee, S. Y.
core +1 more source
Annals of Clinical and Translational Neurology, EarlyView.ABSTRACT Objective To characterize the demographic, clinical, and laboratory features of the Chinese patients of genetic Creutzfeldt‐Jakob disease with T188K variant (T188K‐gCJD), the most common subtype of genetic prion diseases (gPrDs) in China. Methods In this nationwide retrospective study, data from 98 genetically confirmed T188K‐gCJD patients ...
Chun‐Jie Li +11 more
wiley +1 more source
Lubricants, 2022 According to the design requirements of load equalization and vibration reduction for the stern bearing, a water-lubricated stern bearing with self-adaptation capacity is proposed.
Tao He +6 more
doaj +1 more source
Characteristics of Tool Vibration in Ultrasonic Vibration Cutting
Journal of the Japan Society of Precision Engineering, 1979 Characteristics of vibration has been analyzed with a model of lumped system for a tool used in ultrasonic vibration cutting. The analysis shows that the amplitude of the tool vibration during cutting declines not always constantly but catastrophically with increase of cutting force at some conditions because of existing unstable phenomena in the ...
Yoshio TANAKA +3 more
openaire +2 more sources
Advanced Engineering Materials, Volume 27, Issue 6, March 2025.ErB4 and NdB4 nanostructured powders are produced by mechanochemical synthesis. 5 h mechanical alloying and 4 M HCl acid leaching are used in the production. ErB4 and NdB4 powders exhibit maximum magnetization of 0.4726 emu g−1 accompanied with an antiferromagnetic‐to‐paramagnetic phase transition at about TN = 18 K and 0.132 emu g−1 with a maximum at ...
Burçak Boztemur +5 more
wiley +1 more source
Thermoreflectance Detection of Point Defects Resulting from Focused Ion Beam Milling
Advanced Engineering Materials, EarlyView.Focused ion beam (FIB) milling is a common tool for nanoscale material processing, however irradiation damage, redeposition, and contamination can occur. We use several characterization tools to show FIB‐induced effects beyond 1 mm from the milled area.
Thomas W. Pfeifer +3 more
wiley +1 more source
Advanced Engineering Materials, EarlyView.The tribological behavior of 100Cr6 steel spheres textured via Vickers microindentation is evaluated under lubricated sliding by varying both dimple size and density. Fine and dense textures significantly reduce friction across all lubrication regimes, while large dimples increase it.
Farideh Davoodi +3 more
wiley +1 more source
Method of optimizing nonlinear stiffness and damping characteristics of a vibration protection seat system [PDF]
Научно-технический вестник Брянского государственного университетаThe problems of vibrations arising during the operation of ground machines are relevant. Seat vibration isolation systems are used to protect operators from vibrations.
Korytov M.S. +2 more
doaj +1 more source
Experimental and theoretical investigations of a supercavitating hydrofoil [PDF]
, 1957 An experimental investigation of the two-dimensional hydrodynamic characteristics of a thin, supercavitating hydrofoil is described. The effects of twist and vibration of the thin hydrofoil model are considered, and experimental techniques for ...
Lindberg, Z. M., Waid, R. L.
core