Results 191 to 200 of about 3,709 (249)

A new strategy to simultaneous increase in the strength and ductility of AA2024 alloy via accumulative roll bonding (ARB)

Materials Science & Engineering A: Structural Materials: Properties, Microstructure and Processing, 2016
Majid Naseri, Mohsen Reihanian
exaly   +2 more sources

Microstructure and mechanical properties of Al2O3-particle-reinforced Al-matrix composite sheets produced by accumulative roll bonding (ARB)

Materials Science & Engineering A: Structural Materials: Properties, Microstructure and Processing, 2022
Wenchuang Liu, Kenjiro Sugio, Xingang Liu   +2 more
exaly   +2 more sources

Influence of multi-pass FSP on the microstructure, mechanical properties and tribological characterization of Al/B4C composite fabricated by accumulative roll bonding (ARB)

Surface & Coatings Technology, 2019
This paper aims to understand the impact of post-multi-pass friction stir processing (FSP) on the microstructure, mechanical, wear and fracture behaviors of the fabricated 10 cycle-accumulative roll bonded Al-2%B4C composites.
M. Paidar, Ojo Olatunji Oladimeji, H. Ezatpour, A. Heidarzadeh   +3 more
semanticscholar   +1 more source

Mitigation of edge cracking during accumulative roll bonding (ARB) of aluminum strips

Journal of Manufacturing Processes, 2020
Abstract Accumulative roll bonding (ARB) of aluminum alloy strips is often limited by severe edge cracking due to large, single-pass rolling reductions. Edge cracks are often caused by either poor alignment of the roll-bonded strips or lateral spreading.
Brady N.L. McBride, Kester D. Clarke, Amy J. Clarke   +2 more
openaire   +1 more source

Producing multi-layer composite of stainless steel/aluminum/copper by accumulative roll bonding (ARB) process

Journal of Manufacturing Processes, 2019
Mechanical process of Accumulative Roll Bonding (ARB) is one of the severe plastic deformation methods which can be contributed to produce ultrafine grind composites. In this research, multi-layered composite of stainless steel/aluminum/copper after five
Beitallah Eghbali, Masoud Afrand
exaly   +2 more sources

Hybrid composites produced by anodizing and accumulative roll bonding (ARB) processes

Ceramics International, 2014
Abstract In this study, microstructure and mechanical properties of Al/1.6 vol% Al2O3/1.5 vol% B4C hybrid composite produced by anodizing and accumulative roll bonding (ARB) processes were investigated. Microstructural observations and fractography were performed by scanning electron microscopy (SEM). Also, the mechanical properties were investigated
Mohammad Reza Toroghinejad, Roohollah Jamaati, Ali Nooryan, Hossein Edris   +3 more
openaire   +1 more source

Al-based magnetic composites produced by accumulative roll bonding (ARB)

Materials Science and Engineering: B, 2016
Abstract Accumulative roll bonding (ARB) was used to fabricate Al/Ni (with two initial Ni thicknesses) and Al/Ni/Fe 3 O 4 composites. During ARB, Ni layers necked and fractured owing to the difference in flow properties of Al and Ni. In addition, large and elongated clusters of Fe 3 O 4 particles were broken into smaller ones and distributed ...
F. Daneshvar, M. Reihanian, Kh. Gheisari
openaire   +1 more source

Role of shear strain in ultragrain refinement by accumulative roll-bonding (ARB) process

Scripta Materialia, 2002
Abstract The role of shear strain on ultragrain refinement of aluminum during accumulative roll-bonding (ARB) process was studied. The complicated distribution of redundant shear strain through thickness of the ARB processed sheets was quantitatively shown first, and good correspondence between the grain size and the amount of shear strain was found.
S.H Lee, Y Saito, N Tsuji, H Utsunomiya, T Sakai   +4 more
openaire   +1 more source

Effect of inter-cycle heat treatment in accumulative roll-bonding (ARB) process on planar isotropy of mechanical properties of AA1050 sheets

Transactions of Nonferrous Metals Society of China, 2020
The accumulative roll-bonding (ARB) process was applied on the strips of aluminum alloy 1050 in two processing conditions: cold ARB and warm ARB. The results of tensile tests and microhardness measurement show that the warm ARB process exhibits the lower
Fathallah Qods, Mahdi Gerdooei
exaly   +2 more sources

Accumulative Roll Bonding (ARB) Process for Effective Biomedical NiTi Alloys

Volume 3: Biomedical and Biotechnology Engineering, 2017
In this paper, potentials of accumulative roll bonding (ARB) severe plastic deformation (SPD) method to process effective nickel titanium alloys for biomedical application is presented. Effective material properties of biomedical NiTi alloys, including ultra-fine grain microstructure, functional, mechanical, wear and corrosion resistance were ...
Kazeem O. Sanusi, Esther T. Akinlabi, Wambura W. Mwita   +2 more
openaire   +1 more source