Results 121 to 130 of about 3,271,183 (311)

Comparison of chilling requirements among pomegranate cultivars

open access: yes
Pomegranate (Punica granatum L.) is a deciduous fruit tree species that requires a certain amount of winter chilling to enter and overcome the period of dormancy. Pomegranate cultivars exhibit variable chilling and heat requirements for dormancy release,
G. Ferrara   +5 more
core  

Effects of constant and alternating temperatures on breaking dormancy of Peach (Prunus persica L.) seeds

open access: yesRevue Marocaine des Sciences Agronomiques et Vétérinaires, 1995
The effects of constant stratification temperatures on breaking peach seed dormancy were evaluated using seed populations with various chilling requirements. Germination at 20"C increased steadily with stratification time. Sorne low chilling populations
A. Mahhou, F. G. Dennis
doaj  

On the Lightweight Potential of Laser Additive Manufactured NiTi Triply Periodic Minimal Sheet Lattices

open access: yesAdvanced Engineering Materials, EarlyView.
This study explores the lightweight potential of laser additive‐manufactured NiTi triply periodic minimal surface sheet lattices. It systematically investigates the effects of relative density and unit cell size on surface quality, deformation recovery, compression behavior, and energy absorption.
Haoming Mo   +3 more
wiley   +1 more source

Effectiveness of winter temperatures for satisfying chilling requirements for reproductive budburst of red alder (Alnus rubra)

open access: yes, 2018
Background. Experiencing an adequate amount of cold temperatures over winter is necessary for many temperate tree species to break dormancy and flower in spring. Thus, changes in winter and spring temperatures associated with climate change may influence
Janet S. Prevéy   +1 more
core   +1 more source

Electrochemical Evaluation of Compressed Selective Laser Melted AlSi7Mg and AlSi10Mg Alloys in Chloride Environment

open access: yesAdvanced Engineering Materials, EarlyView.
The corrosion performance of AlSi7Mg and AlSi10Mg alloys produced through selective laser melting (SLM) was examined under compressive stress in a chloride environment. Electrochemical analyses, including open‐circuit potential (OCP), potentiodynamic polarization (CPP), and electrochemical impedance spectroscopy (EIS), were complemented by scanning ...
Femi John Akinfolarin   +2 more
wiley   +1 more source

Overcoming Dormancy in Prunus Species under Conditions of Insufficient Winter Chilling in Israel

open access: yesPlants
The phenomenon of dormancy and the evolutionary causes for its development are presented together with the effects of the climatic factors: temperature and light. Shade and darkness have been found to enhance bud breaking in peach. The effects of various
Amnon Erez
doaj   +1 more source

Innovative Processing of Compacted Waste Aluminum Alloy Powders via Controlled Remelting and Solidification

open access: yesAdvanced Engineering Materials, EarlyView.
This study demonstrates an efficient recycling route for out‐of‐spec AlSi10Mg atomized powders through compaction and arc remelting followed by suction casting. By correlating compaction load, cooling rate, and resulting microstructure, we show that intermediate pressures (50–80 kN) and rapid cooling refine dendrites, reduce porosity, and enhance ...
Mila Christy de Oliveira   +4 more
wiley   +1 more source

Consumed by Abdominal Distention

open access: yes
Arthritis Care &Research, EarlyView.
Abimbola Fadairo‐Azinge   +3 more
wiley   +1 more source

Zein‐Based Adhesives: Sustainable Extraction and Application in Bioadhesive Technologies

open access: yesAdvanced Engineering Materials, EarlyView.
Zein is extracted from corn gluten meal using a simple and scalable process with high yield (~90%). The resulting protein is applied in bioadhesives modified with Ca2+ and Fe3+ ions, exhibiting substrate‐dependent adhesion. The findings demonstrate competitive bonding performance and highlight the role of ionic interactions in tuning adhesion ...
Paula Bertolino Sanvezzo   +3 more
wiley   +1 more source

Variable Stiffness Flexure Structures Enabled by Phase‐Change Gallium and Adhesive Interfacial Locking for Soft Robotic Applications

open access: yesAdvanced Engineering Materials, EarlyView.
A flexure‐based variable stiffness structure is developed by integrating phase‐change modulation and adhesive interfacial locking of gallium. The design enables a wide stiffness variability, transitioning from soft, flexible behavior to rigid, load‐supporting performance.
Sungjin Kim   +2 more
wiley   +1 more source

Home - About - Disclaimer - Privacy