Results 11 to 20 of about 2,155,829 (107)
Behaviour of semi-rigid composite connections for steel framed buildings [PDF]
, 2009 During propped construction the steel-concrete composite action resists dead as well as imposed loads. Conversely, the steel section alone resists the floor self-weight in unpropped beams.
Muniasamy, D.
core +7 more sources
The influence of acrylate triblock copolymer embedded in matrix on composite structures’ responses to low-velocity impacts [PDF]
, 2012 In passive safety structures the use of composite materials has increased significantly recently due to their low specific mass and high energy absorption capacities.
Frédéric Leonardi +7 more
core +1 more source
On Surface Grind Hardening Induced Residual Stresses [PDF]
, 2014 Grind hardening process utilizes the heat generated in the grinding area for the surface heat treatment of the workpiece. The workpiece surface is heated above the austenitizing temperature by using large values of depth of cut and low workpiece feed ...
Salonitis, Konstantinos
core +1 more source
Implicit integration scheme for porous viscoplastic potential-based constitutive equations [PDF]
, 2011 This paper deals with a viscoplastic potential-based model allowing thermomechanical damage behavior modeling of porous materials. The model describes rate dependent effects, hardening, creep as well as defects coalescence and propagation.
Msolli, S. +11 more
core +1 more source
Rubber Impact on 3D Textile Composites [PDF]
, 2011 A low velocity impact study of aircraft tire rubber on 3D textile-reinforced composite plates was performed experimentally and numerically. In contrast to regular unidirectional composite laminates, no delaminations occur in such a 3D textile composite ...
DUPLESSIS KERGOMARD, Yann +9 more
core +1 more source
Behaviour and design of composite beams subjected to negative bending and compression [PDF]
, 2012 This paper investigates the behaviour of steel–concrete composite beams subjected to the combined effectsof negative bending and axial compression. For this study, six full-scale tests were conducted on compositebeams subjected to negative moment while ...
Uy, Brian (R9735) +7 more
core +1 more source
Advanced Engineering Materials, EarlyView.Gallium microalloying redirects interfacial reactions in low‐temperature Bi–Sn solders from Cu–Sn toward Cu–Ga intermetallic formation. The resulting Cu–Ga layer suppresses intermetallic growth during thermal aging, alters fracture pathways, and improves interfacial stability.
Iva Králová +6 more
wiley +1 more source
Magnesium‐Retention Assisted Synthesis of High‐Performance Zintl Thermoelectrics
Angewandte Chemie, EarlyView.Mg volatilization and chemical instability during high‐temperature synthesis hinder the scalable fabrication of Mg‐based thermoelectrics. Here, a magnesium‐retention assisted synthesis (MRAS) strategy stabilizes Mg using a sacrificial Mg reservoir and an inert‐gas‐regulated melting environment.
Boxuan Hu +9 more
wiley +2 more sources
Laser‐Induced Graphene from Waste Almond Shells
Advanced Functional Materials, EarlyView.Almond shells, an abundant agricultural by‐product, are repurposed to create a fully bioderived almond shell/chitosan composite (ASC) degradable in soil. ASC is converted into laser‐induced graphene (LIG) by laser scribing and proposed as a substrate for transient electronics.
Yulia Steksova +9 more
wiley +1 more source
Diffusion in Cauchy Elastic Solid [PDF]
, 2022 It is commonly accepted that a starting point of the science of diffusion is the phenomenological diffusion equation postulated by German physiologist Adolf Fick inspired by experiments on diffusion by Thomas Graham and Robert Brown.
Danielewski, Marek, Sapa, Lucjan
core +1 more source