Results 91 to 100 of about 666,453 (214)

Health Hazard Manual For Cutting Oils, Coolants, and Metalworking Fluids [PDF]

, 1991
[Excerpt] The metalworker can be exposed to cutting oils during application by two basic routes of entry: skin contact and inhalation. The higher risk jobs tend to be those with high cutting speeds, heavy oil flow, and continuous contact, which may ...
Brown, Nellie J
core   +1 more source

Study of the System of Forces Acting on the Cutter-Oscillator Under Conditions of Turning With Vibration

Shock and Vibration
This paper investigates the forces acting on a cutter-oscillator during free longitudinal orthogonal turning under regenerative self-oscillation conditions.
Pavlo Tryshyn, Serhiy Dyadya, Olena Kozlova   +2 more
doaj   +1 more source

Impact of cutting forces on surface quality in finish face milling of compacted graphite iron with CBN and nitride ceramic tools

Технічна інженерія
The article presents the results of studies to determine the influence of cutting forces on the quality parameters of machined surfaces as a result of finishing face milling of products made of compacted graphite cast iron (CGI) using round cutting ...
S.I. Radkevych
doaj   +1 more source

Modeling and prediction of cutting forces during the turning of red brass (C23000) using ANN and regression analysis

Engineering Science and Technology, an International Journal, 2017
The life of a cutting tool is greatly influenced by the forces acting on it during a cutting operation. A machining operation is a complex process. It is very difficult to develop a comprehensive model involving all the parameters. The present study aims
M. Hanief, M.F. Wani, M.S. Charoo
doaj   +1 more source

The Assessment of Cutting Force with Taguchi Design in Medium Carbon Steel–Applied Spheroidization Heat Treatment

Measurement + Control, 2017
In this study, the analysis of cutting forces on medium carbon AISI 1050—to which different spheroidization heat treatments were applied—was conducted by the mixed-level Taguchi orthogonal experiment design method.
Şehmus Baday, Hüdayim Başak, Fikret Sönmez   +2 more
doaj   +1 more source

Biomechanics of cutting: sharpness, wear sensitivity and the scaling of cutting forces in leaf-cutter ant mandibles. [PDF]

Philos Trans R Soc Lond B Biol Sci, 2023
Püffel F, Walthaus OK, Kang V, Labonte D.   +3 more
europepmc   +1 more source

Optimization of Machining Parameters to Minimize Cutting Forces and Surface Roughness in Micro-Milling of Mg13Sn Alloy. [PDF]

Micromachines (Basel), 2023
Ercetin A, Aslantaş K, Özgün Ö, Perçin M, Chandrashekarappa MPG.   +4 more
europepmc   +1 more source

Quality of turning using multiedge heads with elastic guiedes and elctromagnetic drives [PDF]

, 2015
Запропоновано експериментальну установку, що складається з багаторізцевої головки адаптивного типу з пружними напрямними для тонкого точіння, в якій керування положення різців у процесі обробки відбувається через електромагнітний двонаправлений привод ...
Lutsiv, I., Sharyk, V., Шарик, Володимир Мирославович   +2 more
core  

Percentage Ratios of Cutting Forces during High-Reed Face Milling. [PDF]

Materials (Basel), 2022
Reznicek M, Horava C, Ovsik M.
europepmc   +1 more source

Research of forces of cutting at porous powder materials [PDF]

, 2008
Наведено результати експериментального визначення сил різання при шліфуванні пористих порошкових матеріалів. Встановлено регресивну залежність для визначення сил різання з уточненими коефіцієнтами від параметрів, що на неї впливають.Results experimental
Bozhko, T., Божко, Тетяна Євгенівна   +1 more
core