Results 111 to 120 of about 7,476,610 (346)

Determination of cutting temperature while milling titanium alloy by face mills [PDF]

open access: yes, 2016
В роботі наведений аналіз особливостей процесу високошвидкісного різання, яке головним чином пов'язують з температурою різання в залежності від швидкості обробки.
Orobchenko, A.   +5 more
core   +1 more source

Simulation on cutting forces and cutting temperature in broaching of 300M steel

open access: yesThermal Science, 2019
In this paper, using the method of single factor experiment, set the test parameters of 300M steel through AdvantEdge software broaching process simulation test, simulation results for the finishing, analyzed the influence of broach rake angle and relief
Changming Zhang   +3 more
semanticscholar   +1 more source

TRAIL‐PEG‐Apt‐PLGA nanosystem as an aptamer‐targeted drug delivery system potential for triple‐negative breast cancer therapy using in vivo mouse model

open access: yesMolecular Oncology, EarlyView.
Aptamers are used both therapeutically and as targeting agents in cancer treatment. We developed an aptamer‐targeted PLGA–TRAIL nanosystem that exhibited superior therapeutic efficacy in NOD/SCID breast cancer models. This nanosystem represents a novel biotechnological drug candidate for suppressing resistance development in breast cancer.
Gulen Melike Demirbolat   +8 more
wiley   +1 more source

Basroparib inhibits YAP‐driven cancers by stabilizing angiomotin

open access: yesMolecular Oncology, EarlyView.
Basroparib, a selective tankyrase inhibitor, suppresses Wnt signaling and attenuates YAP‐driven oncogenic programs by stabilizing angiomotin. It promotes AMOT–YAP complex formation, enforces cytoplasmic YAP sequestration, inhibits YAP/TEAD transcription, and sensitizes YAP‐active cancers, including KRAS‐mutant colorectal cancer, to MEK inhibition.
Young‐Ju Kwon   +4 more
wiley   +1 more source

Определение зависимости температуры резанья от режимов резания и угла скрещивания при чистовом точении валов чашечными принудительно вращающимися резцами [PDF]

open access: yes, 2012
Подобран наиболее приемлемый метод определения температуры в зоне резания. Это метод термопар. Установлена зависимость изменения температуры в зоне резания от режимов резания и угла скрещивания инструмента и заготовки. Приведенные протоколы зависимостей,
Мелконов, Л. Д.
core  

Colorectal cancer‐derived FGF19 is a metabolically active serum biomarker that exerts enteroendocrine effects on mouse liver

open access: yesMolecular Oncology, EarlyView.
Meta‐transcriptome analysis identified FGF19 as a peptide enteroendocrine hormone associated with colorectal cancer prognosis. In vivo xenograft models showed release of FGF19 into the blood at levels that correlated with tumor volumes. Tumoral‐FGF19 altered murine liver metabolism through FGFR4, thereby reducing bile acid synthesis and increasing ...
Jordan M. Beardsley   +5 more
wiley   +1 more source

TEMPERATURE EVALUATION UNDER CURVED-EDGE TOOL CUTTING

open access: yesAdvanced Engineering Research, 2014
A theoretical model for determining temperature on the working surfaces of the tool with the blade shaped profile is considered. Analytical dependences for estimating the thermal state of the blade front face (tooth cutter) with an elliptical profile in ...
Anatoly Andreyevich Ryzhkin   +1 more
doaj   +1 more source

Genetic attenuation of ALDH1A1 increases metastatic potential and aggressiveness in colorectal cancer

open access: yesMolecular Oncology, EarlyView.
Aldehyde dehydrogenase 1A1 (ALDH1A1) is a cancer stem cell marker in several malignancies. We established a novel epithelial cell line from rectal adenocarcinoma with unique overexpression of this enzyme. Genetic attenuation of ALDH1A1 led to increased invasive capacity and metastatic potential, the inhibition of proliferation activity, and ultimately ...
Martina Poturnajova   +25 more
wiley   +1 more source

Investigation of the effects of machining parameters on cutting conditions during orthogonal turning of austenite stainless steel

open access: yesProduction Engineering Archives
The 1.4306 austenite stainless steel has been prominently utilized as a material in the automotive and aerospace industry. Considerable interest has been garnered in the machinability of stainless steel owing to its high strength and poor thermal ...
Kónya Gábor   +3 more
doaj   +2 more sources

Home - About - Disclaimer - Privacy